• We are no longer supporting TapaTalk as a mobile app for our sites. The TapaTalk App has many issues with speed on our server as well as security holes that leave us vulnerable to attacks and spammers.

Search results

  1. M

    Rail extensions

    Want to stretch my 2010 121 vector to a 136 Some brand of extension do not extend the hyfax, other do such tracks usa. Pros/cons? Can the snowflap simply be held up/back with a strap or is a tunnel extension needed, rear heat exchanger, bumper all need to be moved back etc.. Will there be a...
  2. M

    Improving heated grips

    2016 phazer xtx, heated grips are pretty much useless, I've read up on it and understand the ecu is the culprit, poorly designed system. Anyway I was thinking of wiring the stock grips directly to a hi low switch and using a ceramic resistor for the low setting similar to many universal...
  3. M

    Ultramatic clutch

    Why doesnt yamaha use a clutch similar to their grizzly ultramatic clutch. They are bulletproof and never wear out belts. The primary does not spin at idle, it relies on a centrifugal wet clutch inside the engine. Ive heard of people getting 30000km on original belt, I have 13000 hard km on mine...
  4. M

    Code 33 and 34

    Just a FYI, if you get these codes it is likely the coil connectors, can't buy through yamaha but they are common on Ford and Mazda vehicles, I just replaced mine codes are gone, working great now. Should be available at any auto parts store. They are called S819 connectors.
  5. M

    Which cylinder is #1 #2

    I am getting another code 34 last time the culprit was a bad coil connector. 34 is cylinder #2 which side is it. Last time I had code 33 and 34 so replaced both with old ones from a nytro and it was fine for 1000 km. Ford and some Mazda cars use the same connectors.
  6. M

    Throttle position sensor

    I am having sputtering, missing issues with my 2016 phazer at anything less than half throttle (under 8000 rpm) above that it works perfect. I went into diagnostic mode and while check throttle position sensor readings on cluster I noticed the readings are pretty erratic going up to mid...
  7. M

    SOLVED-2016 xtx engine missing, sputtering, stalling

    Problem comes and goes. Starts and idles perfect but sometimes when running slow below 8000 rpm the engine sputters, misses stalls sometimes. Above 8000 it always works perfect. From stand still if you pin it it pulls hard and runs perfect. Sometimes everything is fine. No codes or warnings, new...
  8. M

    Electrical connectors

    Anyone have a source for connectors used on yamaha sleds...specifically the connectors that go onto ignition coils. My 2016 phazer throwing code 33 ends up loose connectors on coils. Dealer soldered in used ones from a nytro but said otherwise only thing avalable is conplete harness for 600.00
  9. M

    Code 34

    Last night my 16 xtx started rough idling and stalling and showing code 34 " Code 34: Open circuit in the primary circuit of the Cylinder #2 ignition coil." Googled it and seems very common ....none of the threads really have final solution. Seems like most suspected wire harness or loose pins...
  10. M

    Yamaha ski skins

    I see you can buy yamaha 9 or 11 inch wide ski skins designed for the a 2010 viking for example, are the vector single keel skis the same, will the skins fit vector skis? I have an extra set of vector single keel skis and woukd like to put them on my 2016 phazer and add snowtrackers and 9" ski...
  11. M

    Ski skins for tuners

    I have a 2016 xtx, are the stock skis tuners and are there ski skins available for these. How are these sleds for "not getting stuck" I am thinking wider skis could only help.
  12. M

    2016 XTX vibration

    I bought a used 2016 xtx with 2000 miles on it. It vibrates quite a bit when accelerating, is this normal for these sleds? Belt looks new but I do not have another one to try (its on order). Is there anything else I could check, seems to be more on the left footwell area but it is felt on right...
  13. M

    Changing skis

    Will skis from a 2010 vector fit a 2016 xtx phaser. I have snow trackers on vector and want to try them on phaser before I buy them for the phazer skis.
  14. M

    2016 xtx issues

    I just bought a used 2016 Phazer XTX with 2000 miles on it and there is still warrantee until this dec. Are there any issue with this sled I should check. would hate to need something after warrantee is up. Thanks
  15. M

    fuel filter?

    I have a 2010 vector with 17000km on it, is there a fuel filter that should be changed on this? what about spark plugs and valve adjustments, are they due yet?, Anything else I should look at, still original seals and bearings in chaincase, all other bearings have been changed. I hear of tons of...
  16. M

    rubbing noise while engine braking

    I just put on a new track and everything is fine except while deceleration or engine braking. It makes a vuv.vuv.vuv..vuv....vuv......vuv.......vuv everytime I let off the throttle most noticeable from 40mph down to zero. Could loose track cause this. I recently retightened it but maybe it...
  17. M

    ski skins and snow trackers

    I noticed on the yamaha website they have ski skins for making you skis wider. They fit Nytro, Phazer and venture lite, Are Vector skis different? I have the single keel style ski not tuner on my 2010 Vector GT. I was going to try them for more floatation in deeper snow. Also would snow trackers...
  18. M

    new track install = vibration

    I just installed a new 32 Talon pre studded 1.25 on my 2010 vector gt and there is a vibration felt through running boards at mid speed but goes away at higher speed. All bearings are good or new, new slides, all bogie wheels are good with new bearings, clutches were dealer serviced before this...
  19. M

    1.6 ice cobra -9 tooth drivers

    will the 1.6 ice cobra fit with a 9 tooth extrovert driver or do you need to go down to an 8 tooth for clearance to the tunnel protectors. Or can you remove the protectors although probably not wise with the studs present.
  20. M

    1.6 lug on Vector

    I have a 2010 Vector with stock 9 tooth extrovert drivers, will a 1.6 ice cobra fit or will I need to remove the tunnel protectors or get the smaller 8 tooth driver? If I have to remove tunnel protectors does it all have to come out or just the front covering the heat exchanger?


Back
Top