Search results

I have a 2018 LTX LE 50th (Red & White) and I'm trying to get the part# for a 50th heated MTX LE seat. I looked on Partzilla and came up with this part# 8KU-F4710-40-00 for $355.16 But I can't tell if is't the Red & White or Blue. Looked up Rocker Dan's build on his 50th. He put a 17 BTX heated...

Not to beat a dead horse, but what's there too say. IMO, they've been ""PHONEING IT IN"" since 2014! :o|

Never thought of counting the plates till after I made the initial post, to pissed off I guess! :o| Counted the plates, 13! #$%&* Srxspec is correct, it's a Viper Chain. Yamaha mislabeled the bag. So I guess I'll play phone tag with Partzilla for an exchange, hopefully the next one is right...

In the process of reassembling the chain case and my new drive chain is to narrow to fit the top gear. Counted the links twice, 86! Ordered the chain off of Partzilla, Yamaha part# 8KC-RAM01-20-00 (86L)/UR. It came in a sealed bag with the correct Yamaha sticker with Part#. Anyone else run into...

Reluctantly I went up to the Big East Show in Syracuse this past Saturday. I've been going since the first show some 20+ yrs. ago so it's tradition. That being said, the show has basically turned into a clothing/helmet show for Klim, FXR, 509, CKX and Mission between a few vendors. Woodies, Stud...

Dug out the spec sheet from the owners manual I keep in the tunnel bag. Spec sheet p/n 2261-708. 2018 SideWinder L-TX 137 LE EB, 86P p/n 8KC-RAM01-20. Thanks Fellas. Need to also call Travis up for some boggie wheels, the two inner forward ones are shot from my studs!

I have an early build LTX LE 50th. SideWinder. I want to replace the factory drive chain. Partzilla has 3 listed. Do I have any way to know witch chain I need other than opening the chain case and counting the teeth on the chain? I'd like to have all parts on hand before preseason maintenance!

We ran it on a stand in my garage, no pulsing in the brake with the wedge in or out. Just for reference, when I put a complete new drive shaft in mine 2 yrs ago I bench tested my wedge with the new shaft and bearing. At 20 ft lbs. the bearing wouldn't budge. I set mine at 35ft lbs in the machine...

My buddy has a 21 T-cat, roughly 1,800 miles. He installed the BOP wedge set at 30ft. pnds. with a loose rotor since new with no issues. It has now developed a grinding thumping sound around the brake. Remove the wedge the sound goes away, reinstall the wedge the sound returns. Tunnel is not...

Looking at the schematic that's the conclusion I came to also! Looks like a job for fall maintenance. Thanks Turboflash. ;)!

I just noticed my handwarmer backlit rocker light is out. Anyone ever replaced just the bulb if possible and whats the procedure? Looked on Partzilla and it looks like the back half of the left switch gear is one piece. Any info would be helpful. Thanks. ;)!

I'll ad my 2 cents. My experience 2 years ago was. Tore apart the brake and bearing , my drive shaft to inner race was .015 thousands. So I tried the dimple method and green loc tite. Let set up over night. Checked next day by running on the stand, tunnel and brake looked to be breathing! :eek...

When I do my seasonal maintenance I'll have the sled up on milk crates. When I fixed the front of the tunnel, louvers and added 5/8 headed rivets. I came up from the bottom thru the engine oil drain plate to get that manifold nut. PIA but can be done. Be sure to start that nut first on reassembly!

Thank's guy's, I"m out for the season due to Covid pneumonia hitting my lungs so my seasonal maintenance has been put off for a while. I've been following the water pump issue posts, my sled has over 11K on it so i figure it's clutch rebuild time and I'll replace the water pump as well. I'm...

I resealed my buddies 21 T-Cat oil tank that was leaking. I used the gray GM rtv that they use on there Dura-Max oil pans! Don't know the part# off hand, it's a little pricey but definitely does the job! When I put on a flat bottom oil pan on my 15 D-Max I literally had to get a 2ft pry bar to...

Not to hi-jack the thread but. What is ""CUTTING THE THROTTLE BODY BARRELS""? As a stock machine trail rider only, is this something I should be aware of?

When I see a Winder or Viper sitting at an intersection, gas station or a choke and puke. I'll strike up a conversation with the owners about mods and maintenance of the pro cross chassis. I'm shocked at how little most know about the quirks and shortcomings of the chassis. Some are very...

I riv nutted both sides of mine as per Rocker Dan's post, along with the disc brake guard and the chain case guard. The factory inner rear rivet on the chain case guard was tight against the chain case and left a little wear mark! :eek: I'm thinking of switching over to SS allen heads rather...

The easiest way to tell if your driveshaft has spun. If it's all stock ""IT'S SPUN, OR GOING TO SPIN""!!! No if and's or but's. One of the shityest design's I've ever seen! Bite the bullet and install Travis's drive shaft wedge, problem solved! If your driveshaft is't worm too bad that is! Mine...

Typical AC/Yamaha bullshit! When I changed out my my driveshaft and bearing 2 yrs ago I bought the BOP wedge. Set the wedge at 40 lbs. Done ""PROBLEM SOLVED""! AC most likely still has a trailer load of drive shafts they'll continue to use cause. ""THEY DON'T SEE A PROBLEM""!!! :o|