• We are no longer supporting TapaTalk as a mobile app for our sites. The TapaTalk App has many issues with speed on our server as well as security holes that leave us vulnerable to attacks and spammers.

Search results

  1. scooterwj

    New driveshaft assembly is available

    Just FYI... I had heard they were back-ordered but I ordered and received one from Partzilla.com. Also I had a nightmare last night that StevewithOCD got rid of his sled and abandoned us... then I woke up.
  2. scooterwj

    BOV not working/blowing off after flashing with new tune

    Hey guys, hope someone can help me understand this. I have the Bikeman Performance BOV on my sled. Last winter I was running the evo Stage 0 tune (fuel correction for aftermarket exhaust - NO HP increase) and when you hit the throttle real hard and then let off immediately you could hear the BOV...
  3. scooterwj

    Question for the boost leak guru's

    I made my own boost leak tester thingy - hope I did this correctly! I found one leak at one of the intake boots.. Tightened the clamp and that went away but I am getting a pretty good air leak out of the small hose that runs into the air box (see pic). I have the Bikeman Performance blow off...
  4. scooterwj

    Melted lower side panel

    Anyone else have this happen?
  5. scooterwj

    Do you carry Torco with you?

    I know this may not belong here but I posted in another forum and go no replies.... If you carry Torco with you on your sled what do you put it in? I'm worried about it exploding/can breaking in the rear storage bag on the back of my tunnel... Also, any suggestions for water bottles that won't...
  6. scooterwj

    Storage containers for Water and Torco Octane boost

    What are you all using to carry water and Octane boost on your sleds in the rear tunnel storage bag? I don't want to worry about anything breaking open and making a mess!
  7. scooterwj

    Chaincase cover bolts torque.. Be careful... Mine just stripped

    I just torqued mine down per the manual at 12 lb ft and 3 of them stripped. I'm beyond mad at this point.... I'm guessing that means I need a new chaincase?
  8. scooterwj

    Is this a good product to seal the inside of the sight glass?

    Just want to seal it up to prevent it from falling in!
  9. scooterwj

    Chaincase driveshaft seal

    I'm in the process of maintenance and replacing my PTO side drivesahft bearing and installing Travis Wedgy thingy... Any reason to replace the chaincase driveshaft seal or do those last for a long time typically?
  10. scooterwj

    Is my driveshaft worn?

    This video is with a new bearing... I do have the thing from BOP to expand the shaft. Is that good enough to just use that to tighten it up or do I need a new shaft?
  11. scooterwj

    Clutching and belt life... Looking for advice and suggestions

    I've done so much reading on here it makes my eyes hurt lol. Bought my SW and rode 519 miles in the winter of 17/18 - totally stock. Before the winter of 18/19 I did the following: EVO exhaust w/tuning - but stock HP. 911 clutch cover Thunder clutching secondary rollers Thunder Big Venom...
  12. scooterwj

    Hard starting and rough idle

    My 06 Apex rtx has developed an issue this season. When it was very cold out (between 10 and negative 16 F) it was very hard to start. I had to pin the throttle to get it started and then feather it around 2,000 rpms for a couple minutes before it would run on its own. When it's warmer out...
  13. scooterwj

    Few issues. Code SD84, flash/flame from exhaust and possible limp mode?

    I'm in the beautiful (cold!) UP right now and have a few things that have happened. First day (Sunday) pulling out of trailer I get code SD84. I shut the sled off, then re-start it and all is good. Later that evening it was about negative 16 degrees, going down the trail if I got on the...
  14. scooterwj

    Is this normal - on my clutch

    Exploded a belt on Tuesday so getting things cleaned up and noticed this area on the clutch shaft between sheeves that is shiny (right side) whereas the rest isn't.... ??
  15. scooterwj

    Chaincase questions

    I opened up the chaincase on my SW to check the 2 screws on the tension roller. They were tight and had green locktite on them. I adjusted my tension to finger tight then 1.5 turns out.... Check out the video, chain seems really loose. I did the same thing on an '18 viper a couple weeks ago and...
  16. scooterwj

    HAD my mind made up to get Curve skis..... BUT

    still can't get them... That is crazy that they are not ready yet. What else should I be considering? I was going to get the Curve skis with 6" slim jims. 80-90% trail riding in the UP of Michigan.
  17. scooterwj

    anyone have the Bikeman BOV?

    http://bikemanperformance.com/snowmobile/yamaha/sidewinder/bmp-ac-9000-yamaha-sidewinder998cc-turbo-blow-off-valve-kit.html Looks like a nice product...
  18. scooterwj

    Clutch offset question

    I know there is days of reading on this topic.... I have the Hurricane clutch alignment tool. I put the tool on and there is a little play, I put a one MM washer in there with the go-no-go part and that made it fit snug. So, is 1 MM of play there too much? I do not have any shims/washers on the...
  19. scooterwj

    Chain tension bolt

    IMG_3624 by scooterwj posted Oct 30, 2018 at 2:07 PM Tried searching :). I'm just busy doing maintenance and upgrades and was comparing the tension bolt on my SW to my SR Viper (both 18's). The SW is in WAY further (I first adjusted both to make sure). The Viper bolt sticks out about another...
  20. scooterwj

    Removing upper suspension wheels

    I see in the service manual that it requires a special tool PN 90890-11117. Is there another way to remove them?


Back
Top