Search results

Hi. I have a 2014 RS Viking Professional and have some problems with it. This is store outside. Tried to start it this summer, ended up frying the starter motor and start relay stopped working. Only tought it was the relay at first, so tried a new relay after 3-4 weeks, but now the ignition...

Hi. Im looking at narrowing the front end of my BTX LE, so looking for tips on who makes a front suspension where you can use the stock shocks? I know about Barcode Performance, but im hoping there is a cheaper option. After shipping and customs fee, im looking at almost $1250 total for the...

So, is there a fix for this yet?

Thanks. But wouldnt the problem be consistent? When i remove the intercooler and silicone hoses, and re fit them again. It works good and makes 15psi for 40-70km before it looses boost again?

2016 Viper MTX with McXpress 270hp kit. Im loosing boost pressure, gone from 15psi and down to about 10psi. Checked the clamps ans silicone hoses between the IC and throttle bodies and it looks fine, cant see any signs of leaking from the hose into the IC either. Changed the silicon hoses to...

I believe all 2015 and have dipstick? Mine does have a dipstick.

Not really. Ive been told that it spits out the excessive oil if it was overfilled?

It takes about 10-15 seconds while catwalking before it comes on.

Thanks, i will contact them.

Thanks, but the issue is not that it's spitting oil out into the intake. When you catwalk over a longer distance, the oil pump sucks air because of the position of the oil tank, and all the oil beeing on the side of the oil tank, and not the bottom where the pick up is.

Anybody?

Hi. Notice my 2016 MTX turbo is getting the oil pressure warning light when doing long cat walks. Is there any fix to this yet, or is just something i have to live with? Thanks

I think I screwed up, I tightened the spring on the rear shock also when mounting the center after spring change. Will try to loose it again. Yes, the standard non fox floats suck, dont like bumps or jumps at all.

I have a 2016 MTX stabdard without the float shocks, changed out the center spring shock to the AC 160#. It feels like it helped a little, but this sled is still to heavy on the steering and it feels way heavy in the front, coming from a Polaris so could be that, but ive tried Arctic cat...

Sadly, its not the Yamaha kit. This is a universial kit i bought at a automotive hardware store for $15. I think i understand what you mean, so it looks like i have to go back and buy the wiring harness too, with the thermostat.

Bought and mounted a heated seat pad and got it placed under my seat cover. There are 4 sires coming from in: 1 ground, 1 12v and 2 for temperaturesensor/thermostat. Anybody have any idea how to wire this? Dont know what they mean by temp sensor/thermostat, is this just for the LOW-OFF-HIGH...

I don't mean to be rude, but im not really paying attention to your posts anymore. Every chance you get, you seem to write something to discriminate McXpress. I know you had some bad experience with a MCX box, but you can't base all of their products on that. I think you would be surprised to...

You can add the leaking chain cases on top of it. Even if it's not developed by Yamaha, they still should deliver the same quality as before.

When the motor with the 190hp kit was tested, they put it into a real stress test. They were running it at WOT for about a minute before it blew. Even if nobody rides at WOT for a minute, i still think the test is valid.

New rod is 2mm shorter then the new one, so the old motor rods and carrillo wont work without the piston. And the new rods are wider where the bearing is, so a old rod on a new crank would make it have 0.9mm sideways play, compared to 0.15mm that is stock. If it works or not i dont know, but it...