Search results

Well I installed an Ohlins in the front of my skid and I'm thinking I installed it 180 degrees off since the refill nipple is pointing down at the track. I'm thinking it may rub the track. Is this installed wrong??

I'm just wondering if it's possible to remove and/or install the skid shocks with leaving the skid in place on a 2005 RS vector. It has a '06 pro active skid from a RS nytro in it which is the same as stock besides rear shock and stiffer springs. Looks like there's room to get to the bolts but...

Just an FYI Trail 15 from Baraga to Chassell is closed for the season in the UP of Michigan. Same with the RR grade from Chassell to Houghton.

Hey guys it been awhile but I am wanting to get my rear skid shocks re-valved and rebuilt. I am way north in the UP of Michigan near Houghton. They used to go to Pioneer but it appears that dissolved awhile ago. Any suggestions on where to send them??? Stock center shock and 2006 Nytro...

This is a map of trails that will be closed in Houghton/Hancock area in the Keweenaw Peninsula of Michigan for the 2019 due to flood damage. It's going to be a rough year with only one trail open to Copper Harbor

I was replacing the bearing on lower clutch side and I'm sure my new bearing isn't pressed in far enough. When looking underneath I see a gap that wasn't there with the old bearing but I can't get it to seat any farther?? Does this look normal or needs to. On on further?

I'm having problems trying to remove my rear axle. Tensioners are full loose but nut and bolt tighten in both directions. Wth am I doing wrong? It' b awhile and I thought I remember a trick with an air gun but I'm afraid I'm gonna snap the bolt off.

Ok went for a 70 mile ride on Friday! Sled ran good! Went to use it to get to my ice shanty on Sat and the temp light came on with the symbol and got warm! Friday night i popped open the coolant cap to check the color of my antifreeze and I thought maybe the cap wasn't screwed in tight when I...

Well I was helping a friend with his primary clutch on his 2005 Rage when I noticed this in the case!! I'm not sure why it happened or what kind of material the case is made out of! Do you think JB WELD would hold up???? Sent from my iPhone using Tapatalk

My '05 Vector is having a strange issue! If I'm on a lake with tracks it'll run fine on low and midrange then when i hold it wide open it began acting like there was water in the fuel! Running dying running dying and eventually went black and shut itself down! After a minute it fired back up...

I decided it was time to freshen up the clutches on my 05 with some low mileage ones from Hibshman.(Thank you very much by the way!) tossed in my ulmer kit and did a little testing! Slight over rev but i was running down a packed road so I expect it to tone down on trail conditions. Here's a...

Well this is a new one to myself! I went to adjust my track tension and the rear axle nut loosens partially thens locks right up! Also my track adjuster on the right side is pretty much maxed out while the left still has play! The track is aligned the same on both sides but I thought both...

Found a blue gear bag and a black trunk bag! Describe the contents if they are yours and we'll get them back to you!! Found them around 1:30pm on Trail 17 heading into Calumet, MI. Hope these find their owners!

Well I had a super bad ride today with a bunch of friends. Snow conditions were bad with lots of snow dust. I came up on a stop sign with a police officer so I slowed down and came to a complete stop when all of a sudden a guy behind me on a Firecat hit me from behind at 70! His spindle caught...

My vector with ulmer clutch kit has developed an overrev up top. When i installed the kit it was hitting right around 8600 up top and after 2000 miles it now is climbing to 9100+. A friend mentioned maybe the belt was getting worn after 2000 miles since I put a new one on with the kit. I...

Well Tuesday we went for a 170 mile ride and it was warm out mid to upper 40's so the trails were extremely loose! I noticed at WOT I was over reving to about 9100 to 9200 RPM's. I am running an Ulmer clutch kit that worked great on hard packed trails in cooler temps it ran about 8700 to 8900...

During a long ride my sled developed a plastic sounding ticking coming from the right side of the sled towards the front. It's really noticeable at about 15 mph and as you get on the gas it eventually disappears. And it's not the cam tensioner as I replaced that last year. I went to look at...

Has any one upgraded their original supertip weights with the newer x weights?? Just wondering if there was a noticeable difference in performance for aggressive trail riding and was it worth the upgrade.

I was just wondering if anyone is using the Klim powercross glove. I have hot handwarmers and Powermadd handguards with extensions so keeping warm isn't much of an issue. Just wondering if they're worth the $90 to pick up a pair. Lost my coldwave race gloves which I loved because they were not...