Search results

I am doing maintenance on a local guys who does guided sled tours and he asked me to install a stud in each ski! He said his other sled has them and they work well. I installed them on the inside rear curved part so they would scratch pavement . Anyone else do this? Curious how well it works

I have a Winder here with slydog command skis Got to ride it around my property and they seem like a really nice ski. Anyone have with some time on the trail with these skis? Looking for reviews Thanks

Hope everyone has a safe and exciting snowmobile season!! Cheers :moon: to all my Doo friends!!

Been out on a small local lake the last few days playing around and getting my clutches dialed in.. Almost spot on.. noticed a little hick up on one of my logs but beside that seems to run really strong Only have a little over 1000ft to run so didn't get to full stretch its legs. I think the...

Just wanted to share this incase someone else out there may have mixed up the avb and wgv plugs or they were installed incorrectly at factory. Was trying to help a guy out who had low boost issues on his hurricane pm tune bunble 240 270 300 would all only boost the 13 lbs He did a full boost...

Hey guys I am trying to help out a friend who upgraded is mcexpress 240 kit to the 270. I am not familiar with the mcexpress kit but does 1turn of wastegate rod=1lbs?. He is set at 8lbs(as it sits) need to increase to 15 Thanks in advance for any info.

Looking over this 22 srx and noticed the torsion spring holders are upside-down . Doesn't look right I am pretty sure they were just install upside-down. Can someone with a 22 srx confirm please

I have a 22 srx in for some hurricane goodies and taking a close look for any updates. I notice they used a harder sealant like loctite 5900? Definitely a different compound then 17 to 21

Got out this morning to test out my sled with the new clutches.. When installing I was meticulous with the whole driveline/bearing installing and clutch alignment. All driveline bearing where installed using thermal expansion and slide right in without mechanical force The alignment was on the...

Anyone in ontario have or know a dealer that may have the chaincase gaskets in stock? I need 3 of them but apparently back ordered

Just got and installed bop' s 4 wheel spacer kit with 19 oem wheels. Everything fits perfect and a cheap alternative with the same results Also got his nut holders (and no I am not talking about his wife's purse..hahaha) Gave them a little personal touch.

The bolt literally fell out when I removed the tensioner. Shift fork pads are 1/2 gone but still sittng on the forks.lol 4000km

Perfect fit with the hurricane header!!;)!

Pulled my plugs out after a season of running closed loop with hurricane pm header tunes. Seems to be running well!!

Been putting lot of attention in heat control for this season. I found riding hard with a header she would get HOT. Especially on mild days. I completed the wrap on the header and going to do the muffler core also since I have 50ft of wrap left.

Stole this idea from my buddy (no1b4me)..

Just got my header blanket today!! Very nice fit on the hurricane header and excellent quality!! Going to be wrapping the 3 inlet pipes up the the blanket and toss the oem shields

Here is the yamaha part # if you need a extra 1.5 mm to achieve closer to spec alignment. This clip is used on all Cat 998 and yamaha used a clip on the shaft. 8JP-RAH06-00 this is not a official part # for the clip for that specific area on our sleds.(it's the same bearing clip as the top...

Is the a wave runner section here? Looking at possibly order 2 for next summer and looking for info. Not familiar with pwc so need to start researching Thanks Marc

Not a big list this year so far..lol - installing * yamaha jackshaft *bdx driveshaft and skf bearings *stm primary *stm secondary * header blanket( may send out header to have it ceramic coated as well) * rebuild/valve qs3 shocks *new brake rotor /pads * slider, carbides and skf idler bearings...