Search results

Rode my sled yesterday . Now when I start it up on the stand in my garage the track starts spinning at idle . It is a 2013 nytro xtx . Do I need to adjust my deflection ?

I am looking at replacement bulbs for my 2013 nytro . I am thinking phillips crystal vision xenon . The package says 67 60w is this to much load on the stator ?

I am thinking about a trip to the black hills in the middle of February, this my first trip out there . I have a 2013 nytro xtx 1.75 and am wondering if I need to mess with clutching at all before I go ? I live in central wisconsin so my sled is setup for low elavation . Any suggestions or...

I am thinking about switching from my schmidt brothers single exhaust to a skinz shorty , or a skinz ultra Q .I am looking for a quiter can since laws are getting strict in wisconsin and the yoop. I have a skinz seat kit on and am looking for a can that works with the seat without having to do...

I have some questions about my install. I already have a schmidt brothers tunnel block off plate , wondering if I need more then this to avoid getting ice build up and a wet leg ? I also have schmidt brothers exhaust .

Has anyone tried these light bulbs instead of doing a full HID swap ?

I started by buying the extended warranty before the 1 year expired , then bought Hygear torsion spring spacers . Just ordered a OFT steering relocate . And I think my last upgrade for the year will be a Skinz seat kit . My sled is a 2013 Nytro xtx 1.75 . Current extras are 2.5 lake effect...

i want to have less plastic behind the seat on my 2013 nytro Xtx . I love the look of a skinz seat and the way it shows off the exhaust but don't want to spend that much money . Does anyone have any other ideas or pictures they care to share ? Any pictures of Excell plastic on ? I have a Schmidt...

I am planning on selling my Nytro . I found something else I would like to try out . I have a 2013 nytro Xtx 1.75 . It was bought new in April as a leftover , I have added Simmons skis , Schmidt brothers single exhaust mo flow console vent and 2.5 inch lake effect pivot riser . Warranty good...

i am thinking of buying a skinz seat kit or WRP seat . I am wondering if they will clear my Schmidt bros single exhaust ? I am trying to clean up the back end by getting rid of the plastic at the back of the seat and sit a little higher also show off my exhaust . Any suggestions or personal...

So i have a 2013 Nytro i bought new as a left over .It has 300 miles on it and last weekend when i got home from riding it didnt want to start .It sat in the trailer over night and temp got down to 0-5 degress . When i got home i turned the key on and didnt hear the fuel pump run ,cranked it...

So finally got to ride my 2013 Nytro xtx , my problem is the single exhaust that i bought new is annoying loud at cruising speed . It is suppose to have the 2 inch quite core in it already but super loud yet . I am pretty sure i have it installed and tightened up correctly .It was so bad i had...

I purchased a single pipe from Schmidt Brothers for my 13 nytro xtx . I am wondering if any one knows the db level for this pipe or if others have had any problems of there own with the law ! It sounds awsome but i think it might be a bit loud . It has the 2 in quiet core in it which i beleive...

So i installed a LE 2.5 pivot riser , my throttle cable seems tight but when running on the stand and turning the bars side to side the throttle stays the same and does not jump . My ? is have others had to re route there cable ? Put a MTX cable on ? My sled is a 2013 xtx . Also if i were to put...

Brand new member hear ! I bought my first Yamaha and my first 4 stroke . I have a new left over 2013 Nytro xtx 1.75 . I swapped out the stock tuners with Simmons gen 1 . I ordered a Lake effect 2.5 pivot riser and base . Gonna try this first before OFT . My real question is exhaust, looking at a...