• We are no longer supporting TapaTalk as a mobile app for our sites. The TapaTalk App has many issues with speed on our server as well as security holes that leave us vulnerable to attacks and spammers.

Search results

  1. A

    05 Vector Inconsistent Idle

    You can sync all you want, (its a good thing to do) but not to cure the symptoms you describe. Those are Constant Velocity carbs and thus the slides are not mechanicaly linked but pulled by vacuum on one side and pushed by air flow the other one. Thing is, those slides have 2 guiding ears which...
  2. A

    RS Vector -07 idle issues

    My vote is for T.O.R.S. Do a search here for details, then bypass it temporarely so that you know where to focus if the case.
  3. A

    Dash/lights takes time to light up.

    <<Battery has plenty of power and is new>> Well, did you measured it ? My old 2005 would voluntary not latching the power relay if voltage under 11.9 volts after engine start. All this bragging about relays is caused (with reasons) by Apex stories i guess :-)
  4. A

    Clutch rattle.... DRIVING ME NUTS

    Since you speak of the 2005 .. Out of the box..... -no rattle for 3 to 4000 miles, right ! -play on the weight pin is there, right ! Only move to the 2005 we found to quiet it out was to repack the sliders with shims (beer cans, whatever) has hard as your fingers allows it. Then good to go...
  5. A

    Clutch problems

    You opened & clean... fine. Did you verify the slack in the bushings too ? Too much slack will tend to bind the moveable and you get stuck in low gear. Did you noticed a notch on your ramp ? How deep are they ? This MY will groove your ramps and rail your primary in the middle by resonance. I...
  6. A

    Clutch problems

    How fresh the springs ? ..hopefuly not 2005 !
  7. A

    Electrical Question #1

    Sorry... i was on my phone and did not see the image correct. You were reading 0.13 ma not 130 ma. So that is nothing there.
  8. A

    Electrical Question #1

    130 ma. ... that cannot be. Too high. Look for 13ma. I would read the manual for that mm meter first. You at 20ma scale, so what you see is not ampere #, its miliamp. At 130ma, don't blink an eye during summer then battery is empty. That's 6 days for a 20 ah unit.
  9. A

    05 Vector Issue

    Pilot jet clogged... As soon as you raise the jet needle, the cylinder kicks in. 2 different jet. Needle jet never plug, Pilot jet very picky. Overnight it in carb cleaner.
  10. A

    2005 Yamaha Rage clutch quiet kit intsall

    Must not be the quiet clutch job i know.... since primary need to be removed & separated. That is, a tied packing of the slider buttons.
  11. A

    2007 Vector Idle Problem

    Mine has clicked 34000 km with this tensionner with no issue. Sleep well. You kind of need a mirror to see the tensionner body all around.
  12. A

    2007 Vector Idle Problem

    ok then. There is an air intake pickup to feed the constant velocity circuit at the front intake side. You can see it from airbox when cover removed. A very tiny hole bottom side and really critical. Carb cleaner it using the provided plastic tube. Top off the the bellows cap of each carb and...
  13. A

    2007 Vector Idle Problem

    Try closing the enrichener faster. You are gas flooding the whole circuit. 3/4 open max when its hot like now, to 1/2 once started, gradually closing to 1/8 during next 20 sec. Do not squeeze trottle. Air is not cold yet. learn what she need on warm up. They all do it. Make sure you have good...
  14. A

    Stator Resistance check 2003 Rx-1 Mountain

    Old thread revived...ehh.. The OP claim a 2.9 ohm from White to ground. This is bad, unless a measurement error. What this test is all about, is to make sure that one of the 3 field is not ground. First thing to be done is to disconnect the plug that goes to the rectifier/regulator module. Other...
  15. A

    EASY FALL START UP

    There's a better, safer & easier solution for this. Disconnect the tank vent and blow into it while cranking. That will push gas back into the pump. When those pumps run dry during off time, they need priming to go again.
  16. A

    Excessive primary clutch rattle

    Back in 2005 with the first 3 holer, the start of the rattle on this clutch. Washers, leather pieces, 0-rings, nylon this or that to fill gaps on rollers, screws, pins...etc. I have tried it all until Yam shim kit for the slider shoes came up but lasted only for a short time. We realized the...
  17. A

    Carb Sync Tool

    What you mean by vacuum line ??? no such a thing.... every carb, cylinder do its own suck. You probably refer to the fuel pump lines. Right ? Fuel pumps need vacuum pulse from cylinder to work. You can connect pumps on carb you do not sync. I think on RX1 you have adjustment seat for idle...
  18. A

    2005 RS Venture help

    Don't seem to be TORS..... Make sure choke pins on all 3 carbs resets when you remove choke... (actually enrichner) If good..... then get her a good treat of ringfree or seafoam... don't bother dismounting to clean.
  19. A

    Changing Oil On a 2005 RS Vector

    Yes... that was he met. There are few stories out there on which the old oring stuck on the base then new one on top caused major oil leak then desaster.
  20. A

    2005 RS Venture Purchase

    35000 km here on my 2005. Original supposed to be BAD tensionner, but i keep the drive clutch quiet so i figure if the chain start singing i may ear it before the engine blows. :-) I am not worried. I use Yami semi-synt and filter since day first. I quitted cleaning carbs by hand being too lazy...


Back
Top