Search results

I bought my 2012 xtx with around 5000 km on it and have never changed nor had any problems with bearings yet. Thinking maybe now that I’m nearing 14 thousand km I should look into it. Trying to decide if I should just get the dealer to do the job or is it not too bad? Can they be changed with...

Last season my HIDs started shutting off randomly sometimes and coming back on. Continually doing this for a couple months. I checked wires, wiggled things around to see if it was a connection problem but couldn’t seem to figure it out. One would just cut out randomly and usually come back on...

was thinking of putting on frogskin vents and riveting through the outside edge of the vent with a washer on each side to help keep the stick on vent in place. Anyone use these vents? Are they thick enough around the edges to rivet? Thanks

I recently covered up the space between the headlight casing and hood cover so I am not getting air from there to the rad. Temp light was on and off on a ride in -10C, i bought 4 frog skin 1 inch circular covers I think I might put by the speedo but also bought four 4.5”x1.125” vents and...

Hello, I was thinking of putting some foam seal tape around the headlamp or hood to stop snow from getting in around there. I have vent screens over every other opening but still have lots of snow getting in, gotta close that space a bit. It’s so open. Could anyone please measure the space on...

I was wondering if it is worth it to get a fuel controller? Easy to adjust and don’t want to deal with going onto a computer like you need to do with the PCV. Are These fuel controls easy to manually set even with out any fuel air sensor?

I’ve looked everywhere online and there’s nothing for Nytro intake mods besides the holes in the cover. Where can I get an intake? I already upgraded to super Q and MBRP header

After putting the MBRP header on I have no more hesitation off the start. Use to bog down a little bit when you’d first touch the throttle but now has that power back. Put in CR9EIX spark plugs and copper donuts

Installing MBRP header with Skinz super Q muffler, who else is running full systems with out PC? How long and how’s it been?

Just changing my header and donuts, wondering if I should buy some permatex ultra copper gasket maker and put some at the connections of the flex pipe to donut and donut to header pipe? Also at the muffler connection. Will this help seal a lot better and last? I also am putting in copper donuts...

Anyone running these plugs? .032 gap, looking to get them for my 2012 Nytro xtx

Anyone use these ball joints from Royal Distributing? Wayyy cheaper than Yamaha’s, says they’re OEM replacement.

I currently run a skinz super Q muffler on the stock header. Going to be changing the donuts soon and was thinking of ordering an MBRP header while I’m going to have it all apart anyway. Was wondering what people think of this header? Anyone use it with a super q muffler? I love the sound of...

I have a 2012 Yamaha Nytro XTX, haven’t looked at the exhaust joints or donuts in like 8 thousand km. Anyone have had these on for a while and know how they hold up? It’s like the same price to buy all new joints and donuts anyways so seems like it’d be worth it. Thanks

Just wondering if I can install these ice scratchers to the skid frame with out any drilling at all? Thank you!

Have a 2012 Nytro xtx. Looked all over and found this 20 tooth gear but says it’s for a 2012 apex xtx . Is this the exact same size as a nytro’s top gear? Or where can I find the gear in Canada? Can’t seem to find very much online, Thanks!

Hi, I just got a new 1.75 backcountry track for my 2012 Nytro xtx and am wondering if I should do any other upgrades to the chain case sprockets or anything else while the tracks getting swapped? Heard that I should get a smaller sprocket to give more torque to spin the larger track. What...

I just got two 12 x 12” sheets of outerwear pre filter sheets and I plan to put them over the metal vents, bottom vent on the oil can side, and the 2 openings on the top by the head light to stop all snow from entering the the machine. Where ever there’s openings. Tired of having 2 or 3 inches...

What size is the plate if it’s flat?

Title says it all, just wondering if it’ll fit before I buy it