Search results

hello, it looks to me like my brake caliper is rubbing on rotor , any ideas what would cause this thanks

has anyone got rid of their teather? i know i will never use it , would like to bypass it n get it gone, plug hole , join wires? is this possible?

would anyone know where a bolt like this came from ? or does it look familiar? i moved my gas tank back a few inches to get bop rov bypass fitting in cover and herd it , was laying underneath tank in center, looks new no locktight on it , washer is built onto bolt and cant come off

would anyone know where i could get a pair of fxr tesm 2x pants to match this gear? in orange n bk, i couldn't find anything in canada where i live , but cross border alot due to job n was able to get jacket n helmet states side , if anyone knows of a place let me know plz thanks!

wondering if anyone knows if this looks correct, i pulled my reverse acuator out for the first time doing chaincase work, when i took outbthe 3 screws it slighly turned clockwise and the spacer or and detent was in this position, i reinstalled the same way, slightly preloaded counterclockwise...

hey, iv had an apex for 13 years now has bin bullet proof i mean stone cold reliable,but i did alot of the apex fixes to get it that way, iv made the decision im going to buy a used winder, can anyone tell me common problems, what to look for? i know nothing about em other than to replace top...

hi , i recentyl got sled out to move, started was slipping , sounded bad, replaced with a used yamaha one problem fixed, i took apart the old one to find nothing really wrong with it,no damage, lots of brush material left, only thing i can figure is where the shaft goes through armature, i...

qick question on a 06 apex starter, i recently pulled out my sled to use my trailer for a week, started fine, got home went to start it back up to pull back in the trailer and it made real bad noise, iv never once had a starter issue with this sled in 10 years, battery is good and fully charged...

hi , was out on my apex and noticed a noise not present in other years! to make a long story short! i need to replace my jackshaft bearing behind the secondary clutch,i have the old one removed, but im havin trouble finding the part numbers for the bearing,lock sleeve and nut and the snap ring...

i have a pair of white c&a ex on my apex, bin on there for while now, still in great shape but white needs clean up or broght back to life! any suggestions?

i have a 06 gt apex and will need a new seat cover soon, it is a black cover with the grey stripe on the side, i see the 2009 red ltx apex also has the grey stripe but it says 4 stroke gen on the seat and mine does not, would like to have that , was wondering if i ordered the one for the 09 if...

has any one used this tool to install clips on a 1.5 inch track? i have had it for a while and was going to replace some clips but the paddle relief is not deep enough, says its good up to 1 .25 paddle track, i havent tried it yet but was curious as to if it would still work? if it would crush...

was wondering the best spot to tap into for power to install heated visor plug? really dont want to run to battery cause have hids on posts already, was going to tap into cig lighter outlet but do u think it would be to much drawing on circuit while using gps in outlet also?i could put slightly...

hey lookin for a gps to put on my sled , for ontario and michigan trails, i dont need the latest and greatest but would like to set destination and know where i am! i would only need to use it one or to times a season so dont want to spend crazy money on it! any suggestions? and price and where...

hey i just turned 20,565 kms. (12,779) miles on my 06 gt, was wondering if i should do valve adjustment soon or when? is it a waste or time or money if dealer did it or what milage should i do it? does anyone have past experience? i just pounded 560 miles hard runnin in 2.5 days in mi and this...

hey iv never been sleddin around gaylord, grayling, mio, mackiaw michigan area , if u r familuar with this area can u start a con versation with me or just reply here! i have a couple questions be for i head up thanks

was wondering if anyone would have an educated guess as to how much hp my sled would have now after a few add on's? its a 06 gt apex , was a 121 now a 136, 23 tooth gear, dalton complete cluth kit,12 3/4 inch frogskinz drilled out in air box,mbrp header pipes with excell muffler and pc3 and...

hey i have a 06 gt apex, my ec shock function quit and I narrowed it down to a bad ecu, (I tried one out of a known good sled), my ecu worked great but just shock function bad, so i ordered a used one off a gye who said it come out of a wrecked 07 apex and worked fine up until the scene of the...

was wondering the best way to remove and install clutch weight rivits, have herd tap lightly and peen with hammer only on rivit not weight, if any one knows or a video link would be cool! also herd 1 gram brings rpm down 100 rpm, true?and if so i assume 1 gram off all 3 weights lowers rpm 100...

hey, have a 06 gt with ohlins shock, waiting on a ecu i ordered to repair adj on fly and really want to set up properly, even when it was working it rode like a board, i am 230 lbs without gear and had the shock rebuilt and revalved at shocktec accordingly, also put pioneer big spring on...