Search results

2019 SRX getting codes C1600 and C1603 handle bar warmer open circuit everything seems to check out so I took the switch apart but there is no contacts to clean up in this switch as it’s just small button switches soldered right on the board has anyone had a problem with a 19 plus control...

I thought maybe my track was trying to eat my tail light at full bottom out but after removing snow flap last night I’m thinking maybe the flap doesn’t bend enough when doing big wheelies and will bend the metal it’s attached to cause it pivots on the bumper mounting points anyone else...

Anyone running this muffler? Currently have a 3” intimidator looking for something quieter and most power and looking at TD Dyno’s this is the next best muffler down from what I have.

What’s the top speed with 290+ tune with a 1 3/4 Hurricane track 146” or similar right now running 1” 192 studs 137” wondering I have lots of springs and gears wondering if difference will be min or large. Thanks

Has anyone else experience the keeper coming out and the valve shim moving? Did you fix it yourself or have the Dealership do the work under warranty?

Blew a belt and sled instantly quite at same time. Installed new belt wouldn’t start without some throttle. Removed plugs all 3 kinda black but not wet. Replaced all 3 and runs the same rough and poor idle.

Tuned 290HP+ Geared 21/37 running about 120mph 1000ft snow Should 21/41 (stock) be faster in 1000ft snow or would 22 or 24/37 be faster then the 21/37?

Got a code C1523 front right shock is there a way to clear this code from the dash or disconnect the batt and reconnect or something. It’s annoying I’m on a sled trip for the weekend guessing the module will be replaced under warranty but would like to get code removed from dash for now

What’s the best way/method to remove old bushings and install news ones in the top gears? and also bushing in primary clutch cover? and bushing in a helix?

I have looked through the service manual that I have a few times and I cannot find the manifold tq specs or sequence

Primary clutch feels abit loose when I grab it and try to move it up and down last time I had it apart the clutch cover bushing was showing signs of wear. Is this a warranty item? Replace the bushing or entire cover?

Yamaha Siewinder SRX Primary roller part number is 8FG-17624-00 weight about 5.9- 6grams Part number 8FG-17624-20 weight 8.9-9 grams I can’t remember now actually right off but are heavier. Thunder Rollers are just slightly heavier then the -00 stock rollers How does the roller weight...

Baseline-SRX 290 tune with anti-lag Dalton Ramps Have done some testing on ice with a few inches snow cover with a VBOX Sport. My 0-60mph times were abit slow from spinning 1320ft 124-125 mph consistently Top speed 126-128 Zero belt issues and clutches are just warm not hot 650 miles I...

What size is the stock chain? Have heard both 3/4” HYVO and 7/8 HYVO 86 link with 21/41 is stock I ordered a 22/24/34 and a 37 from Dave so I’m thinking I will also need a 84 link chain I ran Mobile 1 Synthetic ATF in my 850 is it ok in the Sidewinder also?

Will they work on a 19 SRX? I bought a 4 wheel kit and it needs them to work but the 19 SRX has the big plastic cups so I want to make sure the rails are the same as past years and that the billet adjusters will work.

What hooks better on the lake and snow? 1.450 triggers 1” track Studboy giant V pattern with 4 studs per bar two in outter belt Or Woodys pattern cover full inside of belt with a 3-5-3-5 pattern which on the 5 two studs in outter belt

I cut the zip tie holding the throttle cable to the riser as it was pulling on throttle cable while turning also checked the cable adjuster by riser but it is already adjusted fully loose and I’m still getting this code on brand new Sidewinder. Should I adjust cable near throttle bodies so I...