Search results

In the middle of doing all the bearings for the first time at 12k miles and the last one is the jackshaft bearing pressed in the frame/bulkhead. I knocked out the old bearing and it feels as tight as can be, but the new one rattles slightly when you shake it. Think I got a bad one?

My dad's '16 Vector XTX does not want to start or idle when it cold. It acts like an old carb engine where you have to play with the throttle and keep rpms up for a while. If it does stall it does not want to start, catching and stalling repeatedly. When it does fire up again the rpms...

Nytro has just under 11k on it. I'm assuming that wear on the primary shaft is normal, but when should I replace the bushings/spider rubbers? I'm on my second clutch kit so springs and rollers/weights are fresh(ish). I've also replaced the buttons/spring on the secondary recently.

My father has a '16 Apex XTX with the upgraded fox shock. I sent it out to Hygear for a rebuild since he's sitting at 7600 miles. I've read the easier way to get it back in is to let the air out of the main chamber. Now for the embarrassing question, where is that? Looking on Fox's diagram I...

My '09 Nyro XTX has 12,000 on it and since its my wifes and I don't ride it, I figure its time to replace all the bearings. I have the parts ( I tried to get all new circlips and oil seals so if/when I mangle one getting it out) underlined in red below in my "cart". I'd rather not get part way...

Does this torn rib mean this belt on its way out? There are a couple other spots that fabric is worn on the peak of the inside ribs, but no other missing rubber. I measured the width at the valley of the outer ribs several places around and got 33.4mm-33.7mm so within the 32.5mm spec...

I have the vector gauge mounted and am building a plug and play wiring harness extension (https://www.corsa-technic.com has every single connect I've ever seen, it's a great resource), but have a question. From what I've read I need to add a single pin for battery power to keep the clock from...

I'm looking for a wiring diagram for a efi vector. Anyone have have a picture/file of one?

On my '09 I just reinstalled the skid after installing the star kit and I still have a measured 4" of sag even with both torsions springs on hard. If I pick it up and let it down slowly it will only sag about .5". I greased everything and checked bushing wear when I installed the kit. The...

I'm putting a clutch kit in and wasn't sure if I should replace nthe secondary buttons or not. How worn is "worn" I guess is what I'm trying to ask. They all have flat spots on them, but they definitely aren't cracked. I'll attach a picture of them as soon as I can figure out how to lower the...

Putting my second Nytro back together with Mountain tech 43+2 kit and I decided to try the Pioneer Nylatron bushings. Do I put grease on theses during install and/or periodically grease them? The Mountain Tech a arms don't shave any zerks so I was wondering if I should drill and add some for...

I'm looking for storage for the back of my Nytro XTX and stumbled across the Skinz "Black Box". I know people like their tunnel bags with the exception of them not being water proof so I thought this may work, but I can't find any sort of feedback for them.

I started my tear down of the second Nytro I picked up last winter. I was taking the subframe out to have the grizz gussets welded in so I wouldn't bend it and to paint it because there was some rust on it. When I crawled underneath I found a spot when the frame had been hit. I never crawled...

How have people been talking to and ordering from start suspension? Do they typically use email or phone call? I sent an email a couple weeks ago so I don't want to be one of those pestering customers if their typical MO is they use email land take a bit to respond. It's too early in the...

I picked up a second Nytro xtx last seasons and rode it stock, but now it's time to build it up to match my '09. I'm all set to send the stock shocks to Hygear, but the newer Nytro's don't have clickers or reservoirs in the front. My options are to revalve them as they are, find a used donor...

I'm looking at getting a Proline IS716 hybrid inline to tow my two Nytros. They are now living in a 4 place inline with my fathers and brothers Apex and vector. We are getting rid of the 4 place for two 2 place trailers as we usually just haul the trailer and leave it up for the winter, but we...

I picked up a '14 and had forgotten Yamaha updated the late Nytro's with a engine braking reduction system. I must be one of those rare people that liked the engine braking on my '09. I haven't looked, but I assume its some sort of bypass or hole in the throttle bodies that lets air in when...

When she goes with us my fiance always claims my Nytro and I don't get it back. It should speak wonders to the Nytro and how easily the aftermarket can transform the sled. In my efforts to keep her happy and keep her going I went on the search for another Nytro xtx for myself. After finding...

I'm going to pass 9,000 miles before the season's done and I want people's input on what preventative maintenance I should look at doing. Aside from regular engine/chaincase oil changes, shock rebuilds, numerous exhaust gaskets, I haven't done much. I've contemplated getting either a renegade...

I'm looking at going with a mild turbo kit for sea level trail riding. I know I'll always want more power, but I've had a supercharged truck with about 8 psi for a while. I know when to stop and how to avoid the boost bug. My nytro has 7500 miles on it, aside from driveshaft/jackshaft...