Search results

I've got an 03 RX1 and it is showing the yellow triangle blinking two flashes and the engine icon comes on when it blinks. Does anybody have a list of the codes for this model. It has a broken plug on the oil tank dipstick and I'm wondering if thjat is what it is reading. Ken..........

I'm working on a 03 RX1 and am trying to figure out why it runs like Sh!t. I'm cleaning the carbs and the original owner says he just went through them but I'm having trouble believing it. The Fuel bowl screws were almost impossible to get off as they were half stripped out on the Phillips...

I've got a 04 turbo RX! and yesterday the yellow warning light started flashing two long and one short flashes. I have a manual for the 03 and it says it's the TPS. What does the TPS do on a carbureted sled ? All I can think of is it must adjust the timing according to throttle position...

I built a midmount system and now I need some steering bushings that won't melt. I remember reading about some aftermarket bushing but can't recall the name of the company that sells them. Anybody know ? Ken........

I've got an 03 rx1 with a homemade midmount turbo on it. I am currently running a GT 2560 on it and m looking at a 2860 for it . Would I see any real performance gain by switching ? How much more lag would it have ? Ken.......

Does anybody know how to set up a new MTX Nytro so it will lay over easier. I rode my buddy's sled and I couldn't hardly get it lo lay over in 2 foot of powder. He's running 85 # in the front and I think that might be too much. Ken.........

I've got a 04 RX1 MTN and I had a wire behind the fuse box rub the insulation off and start blowing my 30 amp main fuse down on the starter relay. Then the warning light started blinking and was showing the engine in the display and started blowing the ignition fuse in the main fusebox. I fixed...

My Rx1 turbo has developed a fuse blowing problem. It blows the 30 amp fuse on the ignition relay down by the battery. I have my fuel pump and a/f guage hooked into the same circuit. I have unhooked the a/f guage and replaced the ign relay and it still does it. It doesn't quit running because I...

I just got done building a new header for my rx1 turbo. It's the third one in 8 years that I've had to make. The last one had too many cracks welded up on it so I thought it was time for some new metal. Ken....

I'm looking for the o-ring that goes between the aluminum compressor side and the center section on a Garrett Gt2560 turbo. I had to loosen mine up to turn it and it tore out a 2'' piece. Does anyone know where I can get this part? Ken.......

Does anyone have a takeoff 144 track that they want to get rid of reasonably cheap. We need to cut one down to 12'' for a Snowhawk project. Ken....

Helix Identification ? -------------------------------------------------------------------------------- I've got a secondary clutch with a 8BV 30 helix on it and it doesn't show up in the Yamaha helix chart. I know the 8bv31 is a 43 angle but I would like to find out what this 30 is. Any...

''Smokin' Grass Drags'' Great Falls, MT. -------------------------------------------------------------------------------- Well, i t's getting to be that time of the year for the grass drags. This will be our sixth annual race hosted by the Great Falls Snowmobile Club. The dates are Sept...

Were going up Sunday to do some deep powder riding with the turbo and a snowhawk. The place we ride just got 44'' of new snow in the last day and a half. It's gonna be fun. Ken... http://www.wcc.nrcs.usda.gov/nwcc/sntl- ... 7&state=mt

Joined: 06 Dec 2003 Posts: 459 Location: Great Falls, MT. Posted: Tue Jan 19, 2010 2:53 am Post subject: 03 RX1 Speedo Problem -------------------------------------------------------------------------------- I went out Sat. and my speedo started cycling all over the place. It...

I went out Sat. and my speedo started cycling all over the place. It wasn't reading anywhere near the speeds I was going and was jumping all over even when sitting still. Now it just reads zero mph. Anybody have this problem before?

I'm running a GT 2560 turbo and a efficient 4 into 1 header on my RX1 mountain. The way I have it clutched it's only getting to 9800 rpms. I'm running 17 # of boost and it runs real strong but am wondering how much more hp I would have if I clutched it to about 10800 rpm. Would it be noticeable...

I just redid the downpipe on my homemade frontmount system and went down into the tunnel instead of routing all the way out the back. My downpipe is only 2'' dia. so I weded the bung in with a 1/4'' spacer behind it so the oxygen sensor wouldn't be sticking so far into the downpipe causing...

Well I got a little out of shape yeaterday and flopped my turbo on its side. It took about a minute to get my wits together and turn it back over and then another minute to realize that the fuel pump was still running so it ended up getting flooded real good. I tried cranking on it for awhile...

Does anyone know what I need to do to hook up nos for a one second shot out of the hole. I need something for a better hole shot and was thinking of hooking one nozzle into the charge tube to the intercooler and have it soot just long enough for the boost to come up. Would I need extra fuel for...