Search results

Have got to do the dreaded replacement of the y pipes. mag side clamp had spun around, donut was pretty much gone (2nd set now) and the flange was cracked on the mag side. Pto was good but looking to replace all at once rather than tear this apart again. I'm wondering if anyone has tried the...

I know it sounds kind of crazy but my ripsaw threw a double backer through the heat exchanger yesterday so i'm on the market for a replacement track. I was contemplating an ice ripper xt but i'm not sure it's going to satisfy my traction needs. Always had studded sleds and don't think they...

check out new sled review @ www.maximumsled.com Sounds cool, but not a lot of info and no pics.[/url]

I've got an 06' RTX with the mono shock and wondering if it will swap with the pro active ck from an 07' without any modifications? Basically will i have to relocate the monoshock brackets or do they utilize the same mounting points. I'm a pretty agressive rider and wondering if this...

For those of you who are reinforcing your front pivot arms, are you reinforcing the updated pivot arm or the stock 06' arm that had very few gussets. I replaced my original with the updated "reinforced" arm but am worried it will crack again. i've also broken the rear arm and have 2 small...

Does anyone sell a complete rear bushing kit for the mono?

Looking into replacing my track and suspension since the shocks need a rebuild, both rails are cracked, ripsaw is about shot. I have extroverts so track will have to be open windows. I hope i can part out rear skid to recover some of my costs. I typically ride agressively and would like...

Currently own 2006 RTX and looking to replace. I ride pretty hard and love the top end of the apex. Not sure nytro top end will be enough. Nytro has a lighter chassis which i am very much in favor of. I am looking at a nytro rtx or xtx vs. apex rtx or gt. I ve ridden the nytro a few...

Went for a 200miler today and noticed my sled dripping anti-freeze at every stop. Sled was just at the dealer to have donuts replaced and thought they messed something up. I pulled the plastic on the trail and found the three mounting tabs for the radiator tabs broken off and the radiator was...

The rivets in my tunnel protectors have worn through and the tunnel protector is hanging down in the tunnel. One of the actual brackets that attaches to the tunnel is briken as well. Has any one experienced this and if so can it be repaired without replacing the protectors. I have to...

I've been considering getting a set of ice scratchers and most of the one's i see mount on the slide rails but it would seem these would fail to lube the fron t of the rails where most of the wear occurs. Does anyone make the ski mounted ones anymore? Do the rail mounted scratchers lube the...

I lost most of the clips off the stock rip saw at about 3700mi. At this point i removed the remaining 12 clips and reinstalled all new clips, opened up the closed windows and installed the ski doo extrovert drivers. I lost one clip after about 200miles in great conditions with lots of powder...

Does anyone make a stronger front pivot arm for the monoshock? I've broken 2 now in 3800 miles and wonder if anything else is out there. I also have to replace one drive axle bearing, lost 2/3 of my track clips and blew off 2 rear wheels, transfer rod also came loose and bent. All within...

Has anyone run this setup and how has it performed over stock. I had this upgrade done and have not yet been able to test. If it worked well how did you set it up?

I've got an apex rtx with what looks like a crack in the front suspension arm of the monoshock. Just wondered if anyone else has seen this.

There's been alot of talk about gearing down to the stock gearing of an attack. Has anyone actually done this and what were your results?? Should this be done with the top gear or go up a few teeth on the bottom??? :yam:

Any one else notice the track hitting the rear shock??? :o| I've got an RTX with 144 studs and have chunks missing from the center of the track due to the track slapping the shock. not a problem for long tracks as they have pads next to the shock the track rides over. Looks like not enough...

There are many posts on how to get the gt to rail, and i don't want to be redundant but what are the rtx guys doing. I've been trying to set mine up but cannot get it just right. My floats are at 70psi, Limiter up one hole, transfer a little towards min, the rear shock on the second clip and...

The handlebars on my RTX are slightly turned to the right while going straight. Is there an adjustment for this or does is require doing a total alignment. I did not notice it until the last ride (sled has 500mi) Should i look for other bent parts??? Never noticed it before. :yam:

Wondering if anyone tried anything like Haucks git r done kit or other exhaust/clutching mods. Would like just a little more. Looked at ulmers and prolines clutch kits, anyone have any experience with these?? :rocks: