Search results

If the reverse beeper is disconnected, where would the unplugged connector be found? Do you know if the brake light is fused separately of the running light?

I have an 07 Rage and my secondary "floats" on the shaft. Is this the way it is supposed to be? My friend has a 05 venture, he was told by a dealer the his should not float He seems to be blowing belts way to quick, less than 500 miles. What might be wrong? alignment, tension, or both? What...

I have an 07 Rage and my secondary "floats" on the shaft. Is this the way it is suppposed to be? My friend has a 05 venture and he says his does not. He seems to be blowing belts way to quick, less than 500 miles. What is the normal belt life for these 3 holers?

2007 Rage: Does it have running lights & brake lights? I am not sure if my brake light is stuck on, or if it doesn't work? Is there supposed to be a warning sound (beeper) when the reverse lever is engaged? Is there supposed to be a warning light when the parking lever is engaged? Does it...

A few questions for you all. On my 07 Rage is the tailight a running light and a brake light? I don't know if my brake light is stuck on, or if the brake light isn't working. Also should there be a beeping when the reverse lever is engaged? Also when the parking lever is on should there be...

I purchased an 07 Rage last season. I had Pioneer rebuild my rear shock and I added their 13mm sway bar up front. I ride aggressively and it's still pretty tippy. Does anybody know what the stock front shock spring rates are (It is the base model not GT)? And what replacements are available...

After I get this apart and fixed I will definitely be pulling these bolts out at the end of every season and greasing them !!!

Won't that burn the paint off the A-arms?

I am going through the front suspension on my new to me 2007 Rage. I wanted to inspect the bushings on the left side because I saw some slop in the lower A-arm bushing at the bulkhead. I started to take the ski spindle off the A-arm and the bolts are rusted so bad in the assembly that I needed...

Can someone give me the size specs (OD, ID, bearing size etc.) for the front and rear bogey/idler wheels on my 2007 Rage. I would like to order some after market replacements but want to make sure I get the proper sizes.

I am going to have to replace the bulkhead bushings on my front left suspension. (2007 Rage) How big of job is this? Can the slides be replaced without the skid coming out, on this model?

Hey gone Blue, I believe you were helpful in my my decision to give Yamaha a try. You gave me advice last season on which models had what features and also seat mods. I ended up finding this 07 Rage. Miles are low enough but it's a little rough. I will probably have many Qs until I get...

Picking up a new to me 07 rage tomorrow. One owner 4200 miles. Drive shaft bearings, speedo sensor and oil tank have been replaced. C&A skis and cobra windshield seem to be the only things modded on this sled. Looking for advice on what to do next. Extra wheel kit? Better grip heaters...

That's pretty much where I'm at right now. Time to start taking the easier route. Also I want more ride time, less wrench time. I have 2 dirts bikes, a street bike (Yamaha), a PWC and 2 sleds. Too much to maintain and insure. I am cutting to back to my KTM dirt bike and buying the Yamaha...

I have decided to make the switch a Yami 4 stroke sled for next season. I just sold my Ski-Doo, and my Sea-Doo is going in the spring. Together that should net me enough for and 05-06 model. I know that puts me on the the border of an RX-1 and an Apex. Are there any reliabiilty issues with...

Thank You. I went out and checked and the headlight was out, but not the tail light. I metered the head light plug and it was receiving about 4 volts at idle and peaked around 11 volts when revving the motor. I replaced the headlight and the extra load seems to be keeping the grips cooler...

I have a 1980 340 Enticer that my sons ride around our property. Great old reliable little sled. It looks like a previous owner added heated handle bar grips, as they don't appear stock. The problem is they are wired right into the electrical harness with no switch. They are getting VERY...

Thanks, that good to know. I have been riding dirt bikes way longer than sleds and I instinctively stand up over the rough stuff. So I want to try the newer riding position, it should suit me better.

Hello to TY forum members, first post here. My buddy and I are contemplating switching from "Yellow" to "Blue" for the obvious reasons of reliability and fuel consumption. I thought I had read in a magazine review (a while ago) that the Vector/Rage models went to a rider forward position at...