Search results

WTB MPI STEEL (old style not the newer aluminium ones) blower and crank drive gears Anyone looking to part with any steel blower and crank drive gears. Please PM Mods I hope I can keep this here as the WTB section may not be the best place. THX

I Bought an HID headlight kit a year ago it only one of the 2 lights worked. Seller offered no return only a partial refund. I lot of good that would be like I want to drive around with one headlight but I had no real choice but to agree since that was all he would offer. Seller then stalled and...

WTB/WTT MPI Aluminum blower and crank drive gears Anyone looking to part with any extra / unneeded Aluminum (no steel please) blower and crank drive gears. Please PM Also have 1 or 2 to swap plus a steel P24T. Mods I hope I can keep this here as the WTB section may not be the best place. THX

Looking for instructions To paint lower black belly plastic Does anyone know where to find instructions, for the best type of painting procedure for the lower black belly plastic on Apex. or Does anyone know of anyone who provides this type of painting service?

anyone know what pitch stock yamaha extrovert drivers are 2.52 or 3??

does anyone know if someone sells billet carb boots for an rx1 or have a good mounting solution for Water meth injectors in the stock boots? :die :jump:

Does anyone know if anyone makes billiet carb boots for an RX1 or have a good mounting solution for water meth injectors in the rubber boots?

Can anyone point me in the direction of the post that shows how to make the rx1 seat taller. there was a guy who did it and had adetailed post including materials bought from joanne fabrics. Thanks!

Has anyone modified a stock apex seat to allow for 2 - 2.5 bottles in the trunk? If so any pictures?

does anyone know what fuel pressure should be on an rx 1 turbo (has Bender stage 1)? I normally run at 10 lbs of boost, but have problem and engine won't develope over 6000rpm and wont at that level won't develope any boost. I hooked up a fuel pressure guage and checked fuel pressure. It starts...

Have Rx1 with problem. It runs ok till around 6000RPM then breaks up badly and won't go over 6000 to 7000 RPMs. Doesn't get enough RPM to develope boost. Ran good for first 15 minutes out then turned bad. No warning, indication or event to indicate cause of problem (was not runnig it hard...

I have a Turbo XS RFL (also tried good GReddy) on a Dodge Viper with Paxton S/C. It sounds awsome on the Viper, much better that the Vortech BOV that came with the kit. The same BOV is not even close to as loud on my S/C'd Apex. Both S/C's adding about 10-11 PSI of boost. I think I may...

I have a Bender stage 1 on a 2003 rx1 I am tiring to fix. Owner says the sled ran great for 10 minutes then started to malfunction. It now will only reach 5000 rpms and will not go faster than 40 mph. It feels like it is running an 2 cylinders or is starving for gas, air or spark? I have...

I have a MPI s/c apex that is running very lean at idle & when I let off from Wide Open Throttle. When I start the sled the a/f ratio is 14/1 then after about 45 seconds of running the a/f ratio climbs from 14/1 and pins my gauge at 19.9 to 1. I turn off the machine & restart it happens again...

I have heard you can increase HP on a turbo rx1 by changing the intake valve timing. Have heard you can acheive 20 to 25 hp gain. Anyone done this, know results etc. I'm told its done by elongating holes on intake cam shaft.

Is anyone running a O2 sensor that has user aux inputs? (The following manufactureres upgraded sensors have aux inputs, PLX, Zietronics, Innovative and even AEM I think.) Are you monitoring any of the following with your multifunction O2 sensor. If so, can you tell me where to tap the sled...

Got more props for my trailer than any of my sleds. It does not go as fast but it does not break down much either!

delete

WTB Boondocker sidemount turbo kit for Apex Does anyone have one?

delete