Search results

Well its taken me a bit to get here but I finally cracked the 130mph in 1000' target I was aiming for. 131.38mph on pump gas, with a stock header, drivers, clutches, and track. I ran out of gear for what I was using that day, I'll most likely gear up for the next race and see what...

Hey guys…it was test day for me today. Mostly checking to make sure my octane was good enough for 19lbs boost. 1000’ ice track, soft ice, 39 degrees F. This run was in trail form with no chassis prep. Max spool 19, pump gas. The boost seemed low to me varied around 17-19…..maybe because of...

Hey guys I purchased moflow knee vents for my sidewinder to get rid of some heat. It says not recommended to cut out whole area, but to use drill bit or hole saw….my sled is black and not sure if you’ll be able to see the holes, but I don’t want to be able to see the holes or circles….how did...

Hey guys, I've read all the posts on closed loop and it seems there are a some people with issues with faulty afr numbers, codes, bad 02 sensors or bad modules etc. There are not a ton of threads on closed loop so I'm still on the fence but definitely interested in looking into buying it. Its...

Is there a better way to vent the engine oil instead of having it build up oil in the intake tract? Maybe to the atmosphere?

Can somebody tell me the part numbers for the 2 oil drain plug gasket and oring? I have the oil and filter just need the 2 gaskets for the 2 drain plugs. Thanks

Hey guys…I’ve noticed a new “wind”sounding or “pulsing” type noise while cruising coming from my sidewinder. I just changed the top gear so I looked in the chaincase again and the chaincase all looks fine. My track is pretty tight and skid wheels all seem fine. Not sure where else to look….

Can somebody provide me with the service bulletin for the cracked turbo heat shield? I called my dealer and they have e nothing in their system however I came across I service bulletin I believe on the turbo heat shield….I’m looking for the service bulletin number. Thanks!!!

Does anyone know if 22/38 gears will fit an 84L chain?

Hey guys. After putting on a few hundred miles last weekend I brought sled into garage to melt out all snow and ice. I found red droplets inside skid and track area. My coolers seemed fine, my antifreeze is green. Could these red droplets be shock oil? I can’t find a leak anywhere.

I’m looking to buy a earth x battery for my sidewinder in Canada….anybody have info where to purchase in Canada?

I just picked up a new set of dual keel tuners sma-8jhds for my wife’s 07 136” attak with 108 studs….couldn’t pass up the deal. What carbides (inside/outside) do you recommend for mostly groomed trail riding? I’m not familiar with these skis

Hi guys I have a 2007 attak 136 I just bought it. The limiter strap is an aftermarket strap. Should there be slack in the strap with track on ground and no rider? Right now my strap is taught with track on ground no rider but has slack with rider. I just need a starting point to get this rear...

Hey guys...I have an 07 attack 136”, studded and gutted muffler..stock springs and helix ...has anyone tried stm supertip weights? I have a set of stm 60y weights and want to try them but need a starting point in weight.

Hey guys, I’m going to try out 3 different weights and compare the top speeds...23/37 gears, a few different springs, 41/35 helix. heavy hitters, STM 60Y and Daltons. So far I am very happy with the heavy hitters at 285-300HP. Does anybody have a baseline to try the STM 60 Y at around...

Does anybody have a link to a 2007 apex attak service manual? The Apex is new to me and I’m picking it up next week. It has quite a few miles 9000 but the price was right and it is a clean straight sled. Anything I should look for in specific? The exhaust has been replaced with excel header...

has anybody tried a 24 tooth top gear....I like the idea of large gears for top speed but I want to keep my reverse gear ......want to gear up this winter when using my race map for 1000’ speed runs. For gears I have 22, 24 top and 37,39,41 bottom right now....I’m leaning towards a 22/37 or...

What are your thoughts on cutting down a 137” 1.25 down to 1”? I ride mostly groomed trails, and speed runs on weekends....I will be using max spool 17 most the time in the trails and either max spool 20 or higher for races.....I realize the 1” will get me better speeds in the races I was just...

hey fellas, who has fully clipped their stock ripsaw 2 track? And if so what tool and clips did you buy? Were they installed with track on the sled?

has anybody who has bypassed their roll over valve had any other issues? I have a 2018 sidewinder ltx and am thinking seriously about bypassing my rollover valve like Knapp and Rockerdan did before my oil seal let’s go......is their anymore news about this issue?