Search results

If you look at a picture of the actual arms it looks like they have bushings in them when purchased new, maybe a part that isn’t serviced separately? I looked through a bunch of different listings & don’t see anything different than what we have talked about,the bushings you posted only show...

This is what I saw in the parts diagram

The bushing in the parts listing was originally either steel or aluminum based on color& pics & part #90387-06106-00

I had one but sold it about a month ago,I found out that seat concepts is no longer making any apex, rx1, vector seats, only nytro & sidewinder now, did you check with jim at spa city in New York he may have one & is awesome to buy from

If you increase the idle speed it will help eliminate the clutch rattling,there’s a99% chance that you will have to disassemble & clean the carburetors,these engines have very small jets in the carbs & you will find old fuel combined with plugged jets will be the problem with almost all of your...

Yes it is an rx1 mountain,you will need a guage mounting panel that is completely missing to attach your speedometer to,you stated the machine has been sitting 15years??Did you only change rubber fuel hoses?If you have running issues or warning lights we would need to help you diagnose,does the...

Part interchange shows fitment 2008-2022 nytro,vector,venture, apex part number is different( might work but not showing to be the same)

Wow! Those are super worn!I’ve never seen any that bad, Be very careful pressing those off& the new ones on,pressing can be dangerous & those sprockets take quite a bit of force to remove & install, take good measurements before disassembly,I would check your track really well & make sure you...

When you say cogs im assuming you had new drivers pressed on your driveshaft?( yamaha calls them wheel sprockets) you may have a little play side to side to allow for track alignment,the drivers do not fit really tight in the track windows

Sorry fat fingers & small keyboard on my phone-yes 6206

Yes I agree but they do have special bearings for snowmobile & atv using the same generic number in there part number so be very careful going by that, the tapered id secondary shaft bearing is a good example where it calls 6205 in yamaha part number but is NOT a standard bearing so if ordering...

What did you use/do to clean the body area behind the secondary clutch? Looks like you polished it? Was this done by machine or hand?came out awesome it’s cleaner than when it was new!! Nice job

In the parts diagram I use they are showing the upper chaincase bearing is a fully open 6205 koyo bearing, maybe someone had this apart previously? What brand was the bearing you removed ?yamaha number shows to be#93306-20532-00 should be the same bearing used from 2003-2021 in our applications...

I would say its an aftermarket kit& they sent you a generic bearing, they are almost always either open on both sides or sealed on both sides,simply remove 1 seal with a small pick or flat blade screwdriver, this has been debated at length but im of the thought that when it was engineered they...

If you look at your shafts you should be able to see witnes marks where the seals & bearings ride& you could measure from here, it’s been a minute since I had any apart but if memory serves me correctly you drive seals in until just flush with housing bore, sometimes you can also see witness...

He said he had a good idea not a good idea he was going to tell you about!! Lol

Ive had mine in/out too many times to count, reach out if you have any trouble,if you follow the right steps it’s actually fairly easy

They do some strange things if the battery is bad,as your doing try charging first& if it wont take a charge replace battery & see if problem goes away,depending on battery age& if it went dead& froze will determine if it will recharge or not

When you turn the key on are you getting a display? What is your voltage at the battery jumper leads? These sleds have some known electrical issues but we need to know how it’s reacting

The 09 were bigger diameter & longer with involute drivers,10’ up were same diameter & length but had extrovert drivers, the one I put in my 2003 rx1 mod was from a 2013 & i had it shortened so I didn’t have to use a different outer chaincase cover but got the bigger shaft& extrovert drivers