• We are no longer supporting TapaTalk as a mobile app for our sites. The TapaTalk App has many issues with speed on our server as well as security holes that leave us vulnerable to attacks and spammers.

Search results

  1. C

    Brake Light

    I was told by people i ride with dont you use your brake ? Maybe mines not coming on? I found I don`t use it alot because of engine breaking.But when I do use it i`m in deep to the corner and I usually lock the track.I will check mine when im in the garage next & post the outcome.
  2. C

    Play in upper and lower shock attachment

    As you pointed out in the picture .My bushing and sleeve are brand new from the dealer.I just got the machine back from the dealer and they couldn`t fix the loose shocks after replacing all the parts.They didn`t change the bolts.I looked up the parts and found a new part # for the bolts...
  3. C

    Play in upper and lower shock attachment

    On the front shocks,the bushing does not go into the frame attachment. I could tighten up the bolts so there is no play ,but after a 20 km ride it will be loose again.I`m posting two more pictures.One the threaded part of the bolt is 10mm and it the same diameter of the attachment hole. The...
  4. C

    Pulling out the skid, who has done it?

    loosen off the rear axle bolt and slacken your track all the way.this will give you more room to pull the suspention out.
  5. C

    Reverse

    also had a problem with the reverse only working sometimes.Took it to the dealer and some problem there.Yamaha told the dealer to install a 1mm shim between the sheeve.they did not have the part so they didn`t do the repair. Went home with the machine and put back the 1mm shim I remove to get...
  6. C

    bad lower A arm spindle ball joints.

    I Also have worn lower ball joints.Took the sled to the dealer and they ordered me new lower ball joint under warranty.
  7. C

    Play in upper and lower shock attachment

    Does anyone else have up and down play on there front shocks. Found attachment bolts to be out of spec. Shank of bolt Measures 0.358" Threaded part 0.390".So it didn`t matter how tight the bolts were there was all way play.
  8. C

    clutch HELP?!?!?!?

    When you put your secondary together put the spring in A on the sliding sheeves & #1 position on helix. Hold the helix and turn the sliding sheeve counterclock wise to a twist angle of 45 degrees.Push down on helix and install washer and snap ring.
  9. C

    phazer trouble need help

    I Don`t think you drive light should be blinking,With the key on engine not running.Shift from drive to rev to see if you get a solid yellow light? If you do get a solid yellow start it up and see if your rpm go past 4000rpm. Go back in forth from rev to drive it should give you a solid light.
  10. C

    phazer trouble need help

    Just a thought. If your drive light is blinking,try to turn the gear box or the secondary clutch until the light is on. Motor off.You could be stuck between gears.
  11. C

    So whats the deal now with closing off of the tunnel?

    Thanks for the reply.I will call the dealer and try to get the side panels. Other than this I have no problems with the phazer.
  12. C

    So whats the deal now with closing off of the tunnel?

    Removed the rear tunnel cover.Did not remove fwd cover. went for a 30 km ride.Rear sub frame warm. No water leakage from front cover to leak on my boots. I`m going to leave mine this way.Muffler still get really hot. Weather -4c. Heavy snow fall.Drive 15km turn around tracks are covered in.
  13. C

    So whats the deal now with closing off of the tunnel?

    Hi Everyone I have a 2007 gt with 500 km on it.I covered both tunnel holes. Went for a 55km ride, soft snow -3C.Never shut the engine off. Drove at a good pace,stayed with a 600mxz. About 45 km into the ride my leg was getting hot from the seat subframe.I could not hold my hand on it.The...


Back
Top