Cubby's RX-1
VIP Member
- Joined
- Nov 14, 2003
- Messages
- 734
- Reaction score
- 0
- Points
- 971
- Location
- Willoughby, Ohio
- Website
- www.cubbyscustoms.com
Yo, I need to get a clutch alignment tool. Who sell's a good one???..........Cubby
- Joined
- Apr 13, 2003
- Messages
- 3,158
- Reaction score
- 383
- Points
- 1,663
- Location
- Sauk Prairie, WI
- Website
- www.ty4stroke.com
Cubby
Try this
http://www.thespeedshop1.com/Clutch%20Tools
Or heres the Sled Pro we talked about. It sells for $125.99
Try this
http://www.thespeedshop1.com/Clutch%20Tools
Or heres the Sled Pro we talked about. It sells for $125.99
Attachments
SRXSRULE
TY 4 Stroke Junkie
That is by far the BEST clutch tool you can buy. I love mine, makes alingment a one man job and it dont take 10 trys to get it right. ===SRXSRULE===
Oak Hill
VIP Member
- Joined
- Dec 19, 2004
- Messages
- 540
- Reaction score
- 1
- Points
- 591
- Location
- Owosso, Mi
- Website
- www.airtoolexpress.com
I own a 05 Vector and an 01 Phazer Deluxe - Are the clutch tools the same for these two sleds?
1. Puller
2. Compressor for secondary
3. Primary Clutch Tools for disassembly
4. Clutch alighnment
1. Puller
2. Compressor for secondary
3. Primary Clutch Tools for disassembly
4. Clutch alighnment
I believe the are the same.
hlmrx1
TY 4 Stroke Guru
Hey BBY, what is the purpose of that clutch service tool in the first picture and how is it used? I have one similar to that, but not sure how to use it.
The sled pro tool does both center to center and offset at the same time.
hlmrx1
Hey BBY, what is the purpose of that clutch service tool in the first picture and how is it used? I have one similar to that, but not sure how to use it.
That tool allows you to change weights and rollers without removing the clutch or cover. The forks fits into the spider and you use the leverage to compress the primary spring, then use the second piece across the sheaves to hold the clutch open. I have this tool and it works well for tuning.
Hey BBY, what is the purpose of that clutch service tool in the first picture and how is it used? I have one similar to that, but not sure how to use it.
That tool allows you to change weights and rollers without removing the clutch or cover. The forks fits into the spider and you use the leverage to compress the primary spring, then use the second piece across the sheaves to hold the clutch open. I have this tool and it works well for tuning.
- Joined
- Apr 13, 2003
- Messages
- 3,158
- Reaction score
- 383
- Points
- 1,663
- Location
- Sauk Prairie, WI
- Website
- www.ty4stroke.com
The clutch breakdown tool is used to break down your primary. It removes the spider from the fixed sheave. You simply take the clutch face off along with spring, set clutch into flat plate with the 3 pegs in back of the fixed sheave and turn clockwise to loosen. Its threaded like gas fittings. It may take some heat to get it loosened up, it is very very tight. You will need to use a long breaker bar that insterts into the round piece you put over the top of the spider.
As noted before the service tool is used to change weights without taking the clutch face off and lets you do it on the sled...BBY
As noted before the service tool is used to change weights without taking the clutch face off and lets you do it on the sled...BBY
RX1 Yooper
TY 4 Stroke Junkie
That is a great tool for some sleds, but you don't need it for the RX1. You can only adjust the offset.
grader
TY 4 Stroke Master
sorry yooper, wrong. center to center can also be adjusted, and is often overlooked because people believe the motor is solidly mounted.just loosen the 3 bolts that hold the motor, and you can move it a lot.
black john
TY 4 Stroke Guru
alinment
aliment is a must these moters move a lot. i have found more than a few out of aliment c to c and off set and out of paralel
aliment is a must these moters move a lot. i have found more than a few out of aliment c to c and off set and out of paralel
RX1 Yooper
TY 4 Stroke Junkie
I stand corrected. You are right, I kept hearing there was a ridgid mount.
