Decals Coming Off

[Sevey]

How is everyone making out with their stock decals.

I have frayed edges on the tunnel decals and some on the lower cowls are lifting as well.

What can you do to stop this?

I am scared to know what new ones cost from Yamaha.
MS

 

[mn-kelly]

I had to replace a decal on my side winder and was surprised on how reasonable it was -i was shocked it was much cheaper than a vector decal I needed.

 

[VX1R]

How is everyone making out with their stock decals.

Not so good with the stock decals. I gave my new SRX a "Brazilian" as soon as I got it home just to see what it would look like naked:

Clean shaven....

 

[Dr. FeeLGooD]

I likely will be putting mine up for sale in the fall, and ordered the little ones in the center of the tunnel on each side. They are getting damaged from my boots wearing on them. Each decal by themselves is pretty reasonable, but there are quite a few pieces. I was wondering if all the decals could be protected by a layer of clear paint right over everything when a sled is new?

 

[Crossfire12]

How is everyone making out with their stock decals.

I have frayed edges on the tunnel decals and some on the lower cowls are lifting as well.

What can you do to stop this?

I am scared to know what new ones cost from Yamaha.
MS

Take off and have them airbrushed on no more peel, it will be custom!

 

[markt111]

Not so good with the stock decals. I gave my new SRX a "Brazilian" as soon as I got it home just to see what it would look like naked:

View attachment 160951

Clean shaven....

View attachment 160952

do you have full pics showing the whole sled?

 

[VX1R]

do you have full pics showing the whole sled?

Here's a few...

I should mention that the only reason I gave the SRX a "Brazilian" was that I didn't like how the new 2021 SRX shared the same graphics of the 2021 Venom and Mountain Max models.

As Yamaha's flagship model I think that the SRX needed it's own look:

 

[Bigblue1]

Here's a few...

View attachment 160958 View attachment 160959 View attachment 160960

I should mention that the only reason I gave the SRX a "Brazilian" was that I didn't like this look:

View attachment 160961

And changed the looks to this:

View attachment 160962

Yours is way better!!

 

[hognit09]

WAY BETTER is an understatement. I wish I had that kind of vision to do it like that

 

[PowderFalcon]

i've lost 3 so far.... 1 more big one starting to come loose. super annyoing

 

[TrueBlue]

i've lost 3 so far.... 1 more big one starting to come loose. super annyoing

I have lost a couple also. They were replaced under warranty. What I did was to clean the side panels real good with rubbing alcohol & then get side panel warm with a hair dryer and then add a coating of spray adhesive to back side of decal. After decal was installed heated up decal again & padded down with a clean rag.

 

[Sevey]

Here's a few...

View attachment 160958 View attachment 160959 View attachment 160960

I should mention that the only reason I gave the SRX a "Brazilian" was that I didn't like how the new 2021 SRX shared the same graphics of the 2021 Venom and Mountain Max models.

View attachment 160961

View attachment 160973

As Yamaha's flagship model I think that the SRX needed it's own look:

View attachment 160962

Who did the wrap
Looks good.
MS

 

[VX1R]

Who did the wrap? Looks good. MS

Thanks Sevey. I really like the way it turned out.

Blown Concepts here in MN did the wrap. I collaborated with the owner, Robb on the design.

Blown Concepts is a paid advertiser here on TY also so they support the site.