Obone1
Newbie
Hey fellow RX1 riders. Purchased a 2004 RX1 a couple years ago, sled has 10k on it. Since I purchased only premium 91 octane , with Sea Foam has been used. Sled was started each month without hesitation, ran perfect.
The temperature here is -11c , when starting now engine turns over and backfires, won't start,
choke is fully on. I'm leaning towards faulty ignition coil, spark plugs are new.
Any thoughts?
Tks!
The temperature here is -11c , when starting now engine turns over and backfires, won't start,
choke is fully on. I'm leaning towards faulty ignition coil, spark plugs are new.
Any thoughts?
Tks!
- Joined
- Jun 1, 2004
- Messages
- 7,719
- Location
- sudbury on
- Country
- Canada
- Snowmobile
- 2016 apex xtx
2011 apex xtx
2009 phaser rtx/x
1997 et410t/r
1988 vk 540
take all the rubbers off of the coils and put them back in place. then try and start sled in a dark garage/shed. if the coils are bad, you will see arcing to the head down beside the coils on the bad coils.
you can also try bypassing tors or check throttle cable tension as that can cause issues as well.
you can also try bypassing tors or check throttle cable tension as that can cause issues as well.
74Nitro
VIP Member
- Joined
- Feb 18, 2013
- Messages
- 5,263
- Age
- 52
- Location
- Dublin Ontario
- Country
- Canada
- Snowmobile
- 2019 Sidewinder LTX
When you say spark plugs are new, do you mean brand new today? Or recently brand new and then started and stopped a few times?
RobX-1
VIP Member
- Joined
- Apr 13, 2003
- Messages
- 2,119
- Location
- Coldwater, OH
- Country
- USA
- Snowmobile
- 18 50th Apex XT-X, 08 40th Apex LTX GT, 08 40th Nytro RTX, & 03 RX-1
I think @74Nitro is on to something as although the OP indicated he started the sled each month, he did not mention how long he left it warm up. Just waiting for the flashing yellow gage light to go out that comes on at startup isn't enough, you really need to let them warm up where the heat exchangers are warm to touch. Otherwise, you run the risk of fouling the plugs.
Obone1
Newbie
Tks. To cold today at -16 to work on it.
Plugs have only 2hrs on them, when I ran it during the summer, I would let it warm up, started great a month later.
Can you recommend a good parts store for replacement coils?
Plugs have only 2hrs on them, when I ran it during the summer, I would let it warm up, started great a month later.
Can you recommend a good parts store for replacement coils?
RobX-1
VIP Member
- Joined
- Apr 13, 2003
- Messages
- 2,119
- Location
- Coldwater, OH
- Country
- USA
- Snowmobile
- 18 50th Apex XT-X, 08 40th Apex LTX GT, 08 40th Nytro RTX, & 03 RX-1
Althought it's probably not a bad idea to replace all four of them, I would recommend doing what @maim suggested to first see if all or only some of the coils are arc'ing. I only had to replace 2 out of the 4 on my RX-1 and in doing so, ensured I ordered the updated ones; 8FA-82310-01-00.
As for replacements, I tend to stick with OEM, especially electrical/eletronic componets, but have read here on the forum of others having success with a brand called RM Stator that offers the coils as well as stators and pick-up coils.
As for replacements, I tend to stick with OEM, especially electrical/eletronic componets, but have read here on the forum of others having success with a brand called RM Stator that offers the coils as well as stators and pick-up coils.
Fortress
Pro
Squirt some gas into carbs and crank it over,see what happens
RobX-1
VIP Member
- Joined
- Apr 13, 2003
- Messages
- 2,119
- Location
- Coldwater, OH
- Country
- USA
- Snowmobile
- 18 50th Apex XT-X, 08 40th Apex LTX GT, 08 40th Nytro RTX, & 03 RX-1
Depending on fuel level, is it possilble it ran dry and/or the fuel pump has lost its prime? Here's a similar post where I comment about blowing into the gas tank vent line to re-prime fuel pump. Sometimes, if you just continue to crank, it will fire, but after cleaning the carbs in my RX-1 where I would remove the carb rack, I would always have to re-prime the fuel pump in order for it to fire. Just a thought since it was runing fine previously.
74Nitro
VIP Member
- Joined
- Feb 18, 2013
- Messages
- 5,263
- Age
- 52
- Location
- Dublin Ontario
- Country
- Canada
- Snowmobile
- 2019 Sidewinder LTX
If those new plugs have been run a few times they are most likely the problem.
74Nitro
VIP Member
- Joined
- Feb 18, 2013
- Messages
- 5,263
- Age
- 52
- Location
- Dublin Ontario
- Country
- Canada
- Snowmobile
- 2019 Sidewinder LTX
99% it's plugs.I think @74Nitro is on to something as although the OP indicated he started the sled each month, he did not mention how long he left it warm up. Just waiting for the flashing yellow gage light to go out that comes on at startup isn't enough, you really need to let them warm up where the heat exchangers are warm to touch. Otherwise, you run the risk of fouling the plugs.
Obone1
Newbie
Warmed up to - 11 decided to give it a shot.
All coils on the primary read 2.1ohms, secondary. 5.0 each coil. Are these within spec?
All coils on the primary read 2.1ohms, secondary. 5.0 each coil. Are these within spec?
RobX-1
VIP Member
- Joined
- Apr 13, 2003
- Messages
- 2,119
- Location
- Coldwater, OH
- Country
- USA
- Snowmobile
- 18 50th Apex XT-X, 08 40th Apex LTX GT, 08 40th Nytro RTX, & 03 RX-1
Not sure if typo for primary but assuming you meant .021, it would appear they are within spec. Have you checked/replaced plugs yet?
Obone1
Newbie
When removing the coils, noticed someone had wrapped black electrical tape around 3 of them.
Removed tape and rubber collars. Put them back in the sled, observed spark tracking.
New coils on order!
Removed tape and rubber collars. Put them back in the sled, observed spark tracking.
New coils on order!
Obone1
Newbie
Tks for your help everyone. I'll let you know if the coils were the problem . Ordered a qty of 4 from RM Stator, $307 delivered
-
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.