Search results

I also agree. I'm using 8" Bergstrom triples with the shim kit on my 2009 Rs Venture GT. What a difference! No darting , Smooth steering, turns on pavement.

Hello all Sorry I haven't been paying too much attention to this forum lately because I've been too busy out Riding. The Grand Rapids MN area has about 2 to 2-1/2 ft on the ground. The Thursday storm that dropped rain on everyone else started out as drizzle in the morning but later turned...

I ran the Taconite Trail again from Grand Rapids to the Clearwater Shelter yesterday 12/11. The trail is packing down. There were no bare spots but more snow is needed. The deadfall has been removed from the trail from Grand Rapids to the Clearwater Shelter. No sign of grooming yet. The big...

I took a short run from the itasca Fairgrounds Trailhead to the Clearwater Tail Shelter (about 15 mi one way). There has been no grooming but the trail is in suprisingly good shape. There are many rough spots and you have to snirt (snow + mud =snirt) across the cedar swamps but the trail was...

I'm in Grand Rapids, 33 miles west of Hibbing. There is currently 4 to 6 inches of snow on the ground around Grand Rapids. North of the Laurentian Divide there is 8 to10 inches on the ground. The Marcell area has almost 1 foot on the ground. The DNR opened the gates on the trail system on Wed...

3 to 5 inches predicted for northern MN today/tonight. Last day of deer season. DNR opens trails on DEC 1. Might actually have snow on them this year.

Hello All, I have a 98 Mountain Max 600. I replaced a defective Thottle Position Sensor. My question is the calibration on the sensor. I have a service manual for this sled and am following the procedure for calibration. I believe there is an error in the manual. The formula printed...

You didn't say what year or model your sled was. I will guess that it probably a 2008 to 2010 model. Put your sled gauge cluster into Diagnostic Mode and look at parameter in d:01. In order to get into diagnostics mode, set the e-stop switch to RUN and the ignition key switch to OFF. While...

By sheer peer pressure, I finally got my Filipino wife to say 'Maybe she'll ride with me next winter" on my Venture. If the wife get cold, its "game over". Sooo.. Are there any new developments in warm passenger handwarmers for the 2009 RS Venture GT? ChaseDan

moer pics see attached photo chasedan

RS Venture Brake Connector Photo See attached Photos. I hope this helps. chasedan

Diagnostic code 42 indicates a bad or loose electrical connection to the speed sensor coupler or ECU coupler. It could also be a defective speed sensor or broken speed sensor target. Diagnosic code 84 also indicates a problem with the speed sensor, throttle position sensor, throttle over-ride...

Rock, What does your solution involve? If the problem is voltage drop from the stator coil to the handwarmers, how about using that the handwarmer stator circuit to deliver pilot circuit power to pick up a relay coil instead of powering the actual handwarmers? Then direct connect the...

Are there any new development from Yamaha regarding RS Venture GT passenger handwarmer output? Does any one know how many amps can be pulled from the '09 RS Venture GT passenger handwarmer circiut? I'm considering modifying some old handwarmers from a '98 Vmax to be used in place of...

In order to regulate the dc voltage purchase a zener diode with the desired reverse bias breakdown voltage. Connect it to your full wave rectifier (diode bridge) so that the rectfier reverse biases the zener. Make sure to select a full wave rectifier large enough to handle the current...

I also noticed high noise level I just completed a 230 mile run yesterday. I have a 2009 RS Venture GT. I noticed the track noise is at maximum when travelling on hard pack at exactly 50 mph. If I am over or under 50 mph the noise level drops off considerably. It seems like there's some...

I recently purchased a 2009 RS Venture GT (575 Mi so far). My only complaint with the sled is that the pssenger's handwarmers have very low output , even on Hi setting. Is this problem normal for the sled or do I have to fight with the dealer to get the handwarmer's to crank out some heat...