Search results

I have tried that and also a vacuum from my boat oil change suction canister with no luck. When it is running there is a lot of pressure from the hose going to the air box. Not sure if that is normal. maybe something is broken inside of the oil canister

Thank you. I will try that

I have an 07 gt that was flipped end over end at a good speed the end of last season. The throttle was stuck open and running for a bit until we shut it off. sled would not restart so we towed it. Now we can get it to start but it dies after 30 seconds or so. i get no codes but the oil icon is...

I acquired an ezryde carve display model a few years back and now want to put it in my rx1 mtn. I had the dimensions on a pdf but can not locate it for the life of me. I do remember that Christian at ezryde said it was the same as the apex for mounting locations. Does anyone here have these...

Well best as I can tell from other parts guys is that I was sold a Venture Lite shaft in place of the Phazer shaft. So on to searching for a Phazer shaft and I have a Venture lite reverse for sale

I have an 07 Phazer mt lite. The jack shaft broke on the mag side and caused the clutch side shaft to come out of the reverse box. so after a painfull removal and reinstall of the jackshaft I find that the complete jackshaft with reverse out of an 11 phazer is 2" longer than the one I removed...

I am getting a code 34. Is #2 cylinder mag or clutch side? also are there any rub through areas I should be looking for? I have a new coil getting picked up today to install just looking for other possible problems as long as it is apart

I have an 05 rx1 mtx. Time for new shocks. What is the best option for replacement for the rear skid?

I am interestedbin the phazer windshield bag

Steel bodied non rebuildable. Any recommendations on upgrades for the rear?

After 200 miles of pretty moguled trails my son's phazer Mtx is sitting low in the rear and won't rebound to ride height. Is this the shock being wore out or a torsion spring issue?

I am adding a 7" pro taper bar to my phazer mtx. can anyone tell me if there is a direct replacement throttle and brake line for this conversion? Are the rx/rs chassis the same ends but possibly longer or the attak/vector? I need to add about 2-3 inches to both

Im looking for some used mountain parts. i am not having luck findng used parts. What are some of the salvage guys out west?

My son wants to put pro taper bars on his Phazer mtx. does anybody know if they are the same dimension tube. he was looking at bars from a RMK on ebay TIA

I have recently changed over to 7 tooth 3.0 pitch drivers and a 162 track on my mt rx1. It will not run over 8500 rpm at full throttle. it has 21 /40 gearing. If I switch to a 20 tooth upper will that be enough? the apex mt has a 20 tooth upper. Just thinking with the drivers and track change I...

Thanks but Canada Sled Parts is making me a set. Ordered yesterday morning.

I have an o5 RX-1 mtn. It is a factory 151. I want to change to 7 tooth 3.0 drivers and 162 track. I am having a lot of trouble finding rail extensions for this. Tracks USA says that the rx-1 is different than the rx-1 mtn. I have tried Hartman but they must be closed as no web site or phone...

I am looking to convert my 151 mnt rx-1 to a 162. I am told that the drive shaft for the APEX is the same. Is that the case? Did all the mtn apex's have 3.0 extroverts? Has anyone swapped out for a different skid say a viper 162 or aftermarket ones with great success

I have an 05 RX-1 Mountain. Purchased last fall with a leaking carb. I dropped off at a dealership for repairs before I took it home. It was fine for about 600 of so miles then started having problems with idle. Suddenly idle is extremely low barely staying running. then a while later it is at...

Does anyone know if the switch for the reverse buzzer that is on the lever is supposed to be hot or is it ground? I am guessing ground by the small wires and then the buzzer is always hot when sled is running. Thanks