Lonerider
Lifetime Member
- Joined
- Feb 26, 2010
- Messages
- 156
- Reaction score
- 26
- Points
- 853
- Location
- south west mi
- Country
- USA
- Snowmobile
- 04 rx1, 05 Warrior 06 Attak-w/yamacharger, 07 Attak-Supercharged, 17 Sidewinder TD power trail
I broke the buttons off my secondary again damaging my almer helix. I bought a MAXX roller secondary & a set of 2 speed heel clickers 38/20
( both off TY )
I have a 07 Attak W/ yamacharger, Turk spoke hi-lee of these 2 speeds, Anyone have a set up (USING 2 SPEEDS) they are happy with.
TURK, made a post suggesting Black spring, 1 screw in heel, inner, & tip.
Has anyone tried this, I need more info on what weight of screws to use?
I have 3 sets of different screws, of different weight.
short-2.3 grams, med-3.4 grams, long-4.1 grams & washers .8 grams
( both off TY )
I have a 07 Attak W/ yamacharger, Turk spoke hi-lee of these 2 speeds, Anyone have a set up (USING 2 SPEEDS) they are happy with.
TURK, made a post suggesting Black spring, 1 screw in heel, inner, & tip.
Has anyone tried this, I need more info on what weight of screws to use?
I have 3 sets of different screws, of different weight.
short-2.3 grams, med-3.4 grams, long-4.1 grams & washers .8 grams
IH8CROWS
Expert
- Joined
- Jan 19, 2009
- Messages
- 444
- Reaction score
- 71
- Points
- 758
- Location
- Wisconsin
- Country
- USA
- Snowmobile
- 11 Apex
16 Apex
From Turk:
use stock primary spring & 1 bolt in the heel & see how that works.
From: Turk To: IH8CROWS Posted: Wed Feb 02, 2011 10:16 pm Subject: Re: Heel Clicker 2- speed if that set up does not work go with 1 bolt 1 washer in heel / black hc spring & rest of weight empty.
I'm using the first setup right now and works well. But sled is not broken in yet. So I might have to change it later.
I have an 11'xtx though.
use stock primary spring & 1 bolt in the heel & see how that works.
From: Turk To: IH8CROWS Posted: Wed Feb 02, 2011 10:16 pm Subject: Re: Heel Clicker 2- speed if that set up does not work go with 1 bolt 1 washer in heel / black hc spring & rest of weight empty.
I'm using the first setup right now and works well. But sled is not broken in yet. So I might have to change it later.
I have an 11'xtx though.
the kitchen
Expert
If you want to feel how much pull these weights have then you have to load them with more weight. The stock spring is not strong enough. The HC black works best for me. One screw in tip and screw pluss washer in heel. You want to keep adding weight to the heel as long as your rpm's maintain. I currently run 6.5 in heel and 2grm's tip.
The thing to keep in mind is the heel rotates to become tip wheight at full shift so you may think you need to remove weight from tip to drop rpm's but yhe heel will do the same if loaded. I run the HC secondary yellow at 3-3. Hang on!
The thing to keep in mind is the heel rotates to become tip wheight at full shift so you may think you need to remove weight from tip to drop rpm's but yhe heel will do the same if loaded. I run the HC secondary yellow at 3-3. Hang on!
