tps sensor set up

[Stor]

tps sensor adjustment
I went through my diagnostic menu and it says my tps is at 70% at wot is there anyway to adjust this without taking it to the dealer

 

[idontknowjack]

Are you certain it's not 70 degrees?

 

[sideshowBob]

Read thru all of this thread

Winder TPS(Throttle Position Sensor): Please chime in everyone

After watching Cannondale's video I was curious(bored)so I decided to check out all the functions on our stock factory WINDER Gauge. I was abit taken back to find that my TPS(Throttle Position Sensor) would only max out at 79.6 degrees when I held my throttle lever WOT as shown in video below...

ty4stroke.com

 

[Stor]

Read thru all of this thread

Winder TPS(Throttle Position Sensor): Please chime in everyone

After watching Cannondale's video I was curious(bored)so I decided to check out all the functions on our stock factory WINDER Gauge. I was abit taken back to find that my TPS(Throttle Position Sensor) would only max out at 79.6 degrees when I held my throttle lever WOT as shown in video below...

ty4stroke.com

Thanks
it looks like it's off 10 degrees

 

[justinator]

Thanks
it looks like it's off 10 degrees

Have you verified your throttle bodies are opening all the way? I doubt your tps is off. Look at the linkage on your throttle bodies where cable connects and hold your throttle lever wide open. Now verify the linkage is open as far as it will go by pushing on it to see if it will open anymore. You may not be opening all the way creating your slightly low degree reading on dash

 

[Stor]

Have you verified your throttle bodies are opening all the way? I doubt your tps is off. Look at the linkage on your throttle bodies where cable connects and hold your throttle lever wide open. Now verify the linkage is open as far as it will go by pushing on it to see if it will open anymore. You may not be opening all the way creating your slightly low degree reading on dash

Thanks, I've got a fall plan now

 

[sideshowBob]

From new my SW TPS has showed a relatively low number for full throttle degrees on the Diagnostic display as well as only indicating at full throttle 96-97 % on the Gap flasher live data and data logging.
I have attempted to adjust the TPS but it never eliminated the issue.
I recently replaced the TPS with a new one and the TPS now shows normal values. I don't think the sleds performance was affected in a negative way as it always ran very well with no codes...the values were only an annoyance to me.

Original TPS readings since new

After new TPS installed

 

[1nc 2000]

The gauge shows degrees that it is open.
It is not a percentage value like what the tune shows.
Did you check throttle freeplay?

 

[sideshowBob]

The gauge shows degrees that it is open.
It is not a percentage value like what the tune shows.
Did you check throttle freeplay?

Yes I am aware the diagnostics TPS is degrees but the Gap data is percent...both were a little low.
I checked everything to do with the throttle, cable, hitting the stops ect, even adjusting the TPS could not get the gap data to read 100% at full throttle.
Once I changed the TPS and adjusted it all indications are good....as I posted in pics

 

[1nc 2000]

Ok cool. I didn't realize this was a follow up post.
Now after taking time to look thru the it I get it.
I like to have all I can get too so my tunes can perform as designed.

 

[sideshowBob]

Ok cool. I didn't realize this was a follow up post.
Now after taking time to look thru the it I get it.
I like to have all I can get too so my tunes can perform as designed.

 

[1nc 2000]

From new my SW TPS has showed a relatively low number for full throttle degrees on the Diagnostic display as well as only indicating at full throttle 96-97 % on the Gap flasher live data and data logging.
I have attempted to adjust the TPS but it never eliminated the issue.
I recently replaced the TPS with a new one and the TPS now shows normal values. I don't think the sleds performance was affected in a negative way as it always ran very well with no codes...the values were only an annoyance to me.

Original TPS readings since new

View attachment 170192View attachment 170194

After new TPS installed

View attachment 170200View attachment 170202

Bob i need to replace my throttle position sensor.
Did you use an ohn meter to set base value or just go by readings?

 

[sideshowBob]

Bob i need to replace my throttle position sensor.
Did you use an ohn meter to set base value or just go by readings?

I set the tps using the gap flasher data...I just kept tweaking it until it touched the 100% readout.