Search results

I was attempting to service my bearing as well. I will try and file it a bit but am unsure how to get it off if that doesn’t work. Let me know how yours goes! Thanks for the quick response and good luck!

Were you able to get your rotor off? Mine is giving me the same issue and i can't get it past the end of the shaft either....very annoying! How did you end up getting it off?

Thanks...it would have been rough out on the trail had it worn right through which it was close to doing!

The MPS kit does work real well to lighten up the steering...so much so that I was able to put even more aggressive and longer stud boy shaper bars on as well as more ski pressure by tightening up the limiter strap a hole. I am now using 9” shaper bars on curve skis...it corners like crazy now...

My heated seat element wiring has failed twice now and i am currently waiting for it to be replaced by the dealer under warranty again. I didn’t think I would even use the heated seat but on cold days it’s handy. It a nice option to have when it works. I am installing a kit on my wife’s machine...

Hi guys Just a heads up to everyone that while doing some routine bearing maintenance I noticed behind the secondary clutch that the sheet metal from the bulkhead had been rubbing on the main coolant line and had almost worn right through! This could have been a bad situation obviously if I...

The mystery has finally been solved boys! The first guage failed and suddenly added 10,000 km to my odometer for some reason The replacement guage which was replaced under warranty turned out being defective as well. The guage has now been replaced again under warranty and is now working...

Does the speed sensor read rpm, distance traveled and speed? These are all zeroed out now.

This all started when i took it to the dealer at the end of last season for servicing. From the time I unloaded it off the trailer and drove it across the parking lot to the service bay the odometer mysteriously added a 1 to its total, essentially adding 10,000 km to the total. Quite the...

Thanks for the suggestions guys! The dealer is ordering yet another gauge as he says sometimes warranted parts are returned and then shipped back out without being tested. Baydog... we haven't checked the speedometer sensor..I will run this past the dealer. RPM's are showing zero as well on...

I am at a loss as to why my factory sidewinder gauge is still not registering rpm, odometer and speedometer figures. It turns on and shows fuel level only everything else is zeros. Occasionally it flashes error code u0155. To date my dealer has; -swapped out factory gauge for new one -I had the...

I had a 2014 Viper LTX (13") for a couple years, then eventually handed it over to Dave at Hurricane (big mistake) to have his turbo kit installed. Although the turbo kit never worked as advertised it was in the end a stage 2 240hp kit. I now have a 2017 sidewinder ltx and it is not even close...

That shouldn't be hard these things are beasts!

After having a similar issue with my SR Viper LTX with the cross shaft bending and damaging the tunnel I ordered and installed the RR shaft and bushings from new on the sidewinder and all has been good. Highly recommend upgrading these parts!!

The Nytro...bought the exact same one for my wife and she loves it. Throw some snowtrackers on it and drive it hard! Fun machine!

The leading edges help control the darting. I damaged one and noticed a difference in darting right away. I am happy with the way the leading edges and shaper bars handle on the curves but find the shaper bar durability not great. Next season once they wear out I am going to try Bergstrom...

I have tried the curves with the leading edge with both slim jims and shaper bars. I prefer the shaper bars over the slim jims for aggressive cornering.

I tried the Slim jims with the curve skis on my 2017 sidewinder LTX with 192 studs and was not impressed. I ended up going back to Shaper bars with the 4" leading edge and it handles awesome with no darting issues. The only downside to this setup is the shaper bars don't seem to be very...

I am liking the BOP screen as well.