Search results

It looks like Hurricane is making their own clutch weights again. Big pull clutch arms? I just noticed them on their site. Has anyone had any experience with them yet?

Has anyone used their NS-1 gauge with the i-Act suspension? The NS-1 site says the gauge supports i-act but I am wondering how it functions. How is it displayed on the screen?

Has anyone tried the AC5S 5 position shocks yet? They seem to be a more affordable shock upgrade than the QS3R's , Elka's and such.

I’m trying to help a friend over the phone on a trip. 2024 SRX. When you put the key in the in “on”position, the sled starts. Reverse does not work. Sled sat outside on a very cold and windy night. My best guess was the start/reverse switch is stuck on, or left switch assembly is shorted in...

I am doing the first oil change on my friend’s 2024 Sidewinder GT. 600 miles. Sled has never been back to the dealer. This oil filter was on it Has anyone seen a Wix filter from the factory? Then this was in the pan And this was jammed under the chaincase WTH!! that’s all I saw for now.

Getting ready for a week long trip Are these marks on the ramps of my TAPP clutch anything I should worry about

Has anyone done any testing between the STM secondary vs. a stock secondary as far as tuning options? Question is helix angle comparison, say a Yamaha roller 35 degree acts like a 45 degree on the STM? It seems like the angles dropped @ 10 degrees on the Sidewinder roller clutch vs. the old...

I thought I put some positive news out there. I run INS traction ( Formerly Roetin ) Hornet studs. I get them from an on site sponsor. I have been using them since my 2017 Sidewinder. They are thinner profile than most. I also like that they will snap off instead of bend. I figure they will...

With the low snow conditions here the last few years, my hyfax have been taking a beating, especially at the bend. Has anyone found a wheel set up you can place in that area to slow down some of the wear? I was looking at something like this...

I have installed and am testing a clutch weight I used extensively in the past but abandoned in 2018 because of reliability issues and the owners unwillingness to address them. Long story, I used heelclicker and heel clicker Drag-n-fly weights since they came out in the early 2000's . They were...

https://maine.craigslist.org/snw/d/bryant-pond-08-apex-gt-ltx/7815174577.html prices are starting to get to pre-covid levels around here

this seems cheap compared to what I have seen these sleds advertised at previously. https://glensfalls.craigslist.org/snw/d/minerva-2009-yamaha-venture-gt/7814235031.html

looking for a wiring diagram for heated seat 2022 sidewinder

Has anyone been able to thread the stock Yamaha weights? I took the rivets out of a stock weight and was wondering if i could thread the hole and use set screws instead of rivets. I know the material they are made of is hard as nails. The other thought I had was to put a small 6mm bushing in...

I am putting around with my clutch this morning. I am looking for some RPM and instead of buying another set of Dalton weights I am looking at what I have in stock. My Dalton current weights are too heavy at 75 grams. I have a set of G-Force weights at 71.5 grams. The G-Force weight has a...

I pulled my Hurricane flasher out storage box today to plug it in and check all the flashes I have on it. When plugged in to the laptop, the GAP application cannot find the device. On the flasher, the red light comes on but blinks, in between blinks it pulses blue. Is my flasher junk? Has...

I have a brand new 2024 SRX in my shop to install studs. 84 miles When I move the sled or shut it off, I can hear a small "whine" as the turbo slows or stops spinning. Sounds like a bearing noise. I have 2 other Sidewinders right next to it, one with 2200 miles and the other with zero miles and...

Took my skid out yesterday to assess the damage from our 4-day saddlebag ride last year through Quebec. we ran into some of the worst conditions I have ever ridden in. I knew there was pre-mature wear on some parts but was unprepared for what I found on my lower shock. I know these bushings...

THIS IS FOR SALE LOCALLY https://vermont.craigslist.org/mcy/d/randolph-antique-yamaha-lb50pg-moped/7650603158.html

I have been out of the Nytro game for a while now and am wondering if you guys have found any new ways to make the front end better. That was the main downside with my Nytro XTX in the day. The reason I ask is because beside the front end I liked the rest of the sled. There also seems to be some...