Search results

Just did this on my new pre drilled track installing 144 Stud Boy Power Points. You will need 48 double backers and 48 singles. Also, just a warning, the pre drilled holes are very tight and they are a pain to put in. Your hands will be sore.

Does anyone know if there are many changes between the 2013 and 2014 XTX other than the ski's? Is the slider wear issue corrected on the 13's? I currently drive an 06 Apex and am looking at a leftover 2013 for around $11,200. Any input would be appreciated.

2006 Apex Er. Posted a topic several weeks ago about a strange rattle, clunking noise. The noise was very strange and several people replied that it sounded like bearings in the chaincase. Well, I put 550 miles on the sled with the rattle and the sled ran great, just the noise. I took the...

Thank you very much for your quick reply. That is what I was looking for.

2006 Apex ER. I have a bearing going out in my chaincase and will be changing it this weekend. I want to change all of them while in the case. Does anybody know what size and number the bearings are? The dealer has to order them for me which takes me into next week so. A local bearing...

OK Thanks. I will check that. Is this bearing easy to change, can you change it without pulling the shaft out?

Ive always greased both every season following instructions from this site. This year, I replaced the driveshaft just for a piece of mind. After running it on the stand, i pulled the secondary and checked the jack bearing. Looks good, well greased.

2006 Apex ER with nearly 6500 miles. Only rode 500 miles last year and 30 so far this year due to poor snow conditions. This weekend, I put 35 miles and started hearing a strange sound, almost like a grinding or rattle sound near the left front side. Checked belt and discovered it peeling...

Tipped my 06 on the left side a few years ago and fouled the plugs.

I currently ride an 06 Apex and will be riding a buddies 2011 next weekend (nice buddy). Do you run premium in the new ones or just 87 like the 06? Thanks

Here's the link. http://grandrapids.craigslist.org/rvs/1617319783.html

I see your in Michigan. There is a guy in the Grand Rapids area that builds heavy duty lifts with wheel kits. They cost $220.00 and are either black or red. They have a heavy duty jack and can by raised by hand crank or drill. I bought one in the fall and he posts them on Craigslist often...

2009 Phazer RTX, 1000 miles, new this fall. My buddies Phazer suddenly shut down at idle. Sled would not restart at first but was eventually able to get it running. It is only running on one cylinder. Could this be a fouled plug? Has anyone had this similar problem occur? He was riding...

Im trying to replace the rear upper guide wheels on an 06 Apex ER. It was a pain to remove the old ones and even harder to put the new ones on. The bearing is a tight fit on the shaft and I was wondering if anyone had any tips to make it easier. Thanks

What side is it safe to turn the sled onto? I recall people fouling plugs if they turn it on the wrong side to perform service.

Just replaced mine on an 06 Apex. It was shot however I never put it on a battery tender. I removed it every Spring and kept it inside

Are the CR10 pre gapped, if not what should they be at?

Got them out by welding nuts on the top and they came out smooth. Put never seize on the new ones I installed. Thanks

Im gonna try the Dremel way. If that does'nt work I'm gonna weld a nut on the top and wrench them off. What a pain, this made my two hour job a two day job.

I began the donut replacement following the directions found in the FAQ section. Everything was going great until I reached the point where I had to loosen the two allen type bolts near the front of the Y pipes. The rear bolts were simple but the allen type ones were very rusted and I stripped...