stomper
TY 4 Stroke Master
I’ll have to research how to do that.
- Joined
- Jun 1, 2004
- Messages
- 7,834
- Reaction score
- 2,034
- Points
- 2,103
- Location
- sudbury on
- Country
- Canada
- Snowmobile
- 2016 apex xtx
2011 apex xtx
2009 phaser rtx/x
1997 et410t/r
1988 vk 540
Brotherdan
Expert
- Joined
- Sep 8, 2017
- Messages
- 372
- Reaction score
- 146
- Points
- 458
- Location
- Belmont,maine
- Country
- USA
- Snowmobile
- 2011 apex xtx blue, starr suspension,gytr front shocks,camso 1.5 track cut down, snowtrackers work in process,2003 rx1er originally 121 converted to 136"monoshock 2 ck136 rear suspension with clicker vector ltx shock,muffin works tunnel extension, seat concepts(wrp) seat,apex hooked handlebars converted to all underhood wiring,8"lake effect billet aluminum riser,gytr frontshocks,yamaheater hand warmer kit,rocks ridelite,rocks power supply, rocks heated bag,, tunnel braces,blue skid plate,garmin gps, aggressive snowtrackers on apex single keel skis,rollerski ski wheel kit,108 warthog studs&blue studboy backers,pioneer wheel lowering kit, dupont slides, 4th wheel kit,yamaha saddle, tank& windshield bags, powermadd led handguards, bar mount mirror kit, apex radiator& electric fan added, apex rear cooler,autometer temp guage, apex new style large diameter drive shaft with extroverts machined for chaincase,thunder products clutching,1987 enticer 340ltr 2100miles,1984 enticer 340,1996 wolverine 350,big wheel kit,winch,racks,k&n,full skidplates
Did you seperate each carb from each other?if not I don’t beleive it’s an issue with carb sync.
74Nitro
VIP Member
- Joined
- Feb 18, 2013
- Messages
- 5,485
- Reaction score
- 4,158
- Points
- 1,853
- Location
- Dublin Ontario
- Country
- Canada
- Snowmobile
- 2019 Sidewinder LTX
Correct. Idle would be erratic if carbs were out of sync.
stomper
TY 4 Stroke Master
I’ll have to research how to do that.
sorry double post
sorry double post
Last edited:
stomper
TY 4 Stroke Master
No I didn’t separate the carbs. All I did was remove the bowls, jets and slides, I also replace the needle and seats with new in all carbs, Cleaned the jets and passages and put them back together. That’s it.
Brotherdan
Expert
- Joined
- Sep 8, 2017
- Messages
- 372
- Reaction score
- 146
- Points
- 458
- Location
- Belmont,maine
- Country
- USA
- Snowmobile
- 2011 apex xtx blue, starr suspension,gytr front shocks,camso 1.5 track cut down, snowtrackers work in process,2003 rx1er originally 121 converted to 136"monoshock 2 ck136 rear suspension with clicker vector ltx shock,muffin works tunnel extension, seat concepts(wrp) seat,apex hooked handlebars converted to all underhood wiring,8"lake effect billet aluminum riser,gytr frontshocks,yamaheater hand warmer kit,rocks ridelite,rocks power supply, rocks heated bag,, tunnel braces,blue skid plate,garmin gps, aggressive snowtrackers on apex single keel skis,rollerski ski wheel kit,108 warthog studs&blue studboy backers,pioneer wheel lowering kit, dupont slides, 4th wheel kit,yamaha saddle, tank& windshield bags, powermadd led handguards, bar mount mirror kit, apex radiator& electric fan added, apex rear cooler,autometer temp guage, apex new style large diameter drive shaft with extroverts machined for chaincase,thunder products clutching,1987 enticer 340ltr 2100miles,1984 enticer 340,1996 wolverine 350,big wheel kit,winch,racks,k&n,full skidplates
I accidentally replied to an old post did you bypass the tors by reconnecting on the harness side?
stomper
TY 4 Stroke Master
I will definitely check this out. Thanks
stomper
TY 4 Stroke Master
Yes I connected the bullet connectors together on the harness side but it never made a difference.
Last edited:
stomper
TY 4 Stroke Master
Haha this is getting confusing. Got a couple threads going about this problem. Didn’t mean to do that. I guess I should have posted this on my first thread.
