Search results

Can anyone help me with my jetting. I have a turbo running 8-12 pounds of boost on my 2003 RX 1. I have 17.5 pilots 130 mains and the needles in #4 (somebody told me not to go full rich on needles). Ride at 1000 feet in MN MI and WI. At Idle I see 12.7-13.2 at start up...low 12's after...

Thanks madsledder, that's what I went with, test run soon. MM

OK , my floats are either waayy off or I am not doing this right. I haven't even been drinking, (maybe that's the problem). How the heck do you measure and adjust the float level? I have a 2003 RX 1 w/Simon CPR Turbo. I have the CD and it says the float level should be 11-15mm but the...

floats This is a first, I found the procedure and specs...on a CD. Thanks, back to work. We have over 2 feet of snow and I am garage bound. Just aint right. MM

Hello again, Man, these carbs were so dirty, no wonder it wouldn't run very well. Anyone know how to check float heights (what is the stock setting) and how do I adjust them? Never done this before. Thanks, any helpful suggestions? Muskrat

clean The intercooler is pretty clean especially since it was full of gas. Must have a needle stuck or choke stuck because gas was going into the intercooler and engine at a very fast rate. Actually a good thing it didnt start , that could have been a problem. The gas issue happened once...

hi Thanks, is it a DIY job or does it mean Turbo rebuild? M

Hi everyone, it's been a long time since I have been on this, the coolest site for Turbo Heads. I have a front mount simons CPR kit on my 2003 RX 1. I am getting oil in the charge tube and a little in the intercooler. Thought this was coming from the breather, that goes into the air filter...

really Thanks for the info, I thought the magic number was 14.7 minus one or 1.2 , so 13.5. Does it matter on how much boost you run? Thanks. Muskrat

pilots sounds like pilot jets may be clogged. I couldnt get mine cleaned so I bought new 22.5's. That's all they said were available. I idle very rich 10.8, clips lowest (richest ) and 130's. My mid range is 12 to 12.5 and WOT 12.5 to 13. 8 pounds and 10 pounds both. Someone said they had 20...

innovate Man, I just got done with installing that brand...it was the same. Got E9. E9 is low voltage. I had pulled power off the ignition switch and it was only 11.4. A ONE VOLT loss from battery. Insane recommended a bus off battery to run stuff, I couldnt find parts so I wired lc 1 from batt...

Hello everyone, Just wanted to say thanks for all the replies to my post, it was a big help. I FINALLY got her on the snow. Put 120 miles on her and no problems. A few little things like 11.0 or in the 10's at idle and very low power, have to go back to leaner pilot jets I guess. They must...

oil Well , getting oil and cant find any damage. Drove it 120 miles...no problems, sound no different and no louder. Muskrat

hi Thanks Blue Shadow, I have that setup and will check it now. I also have a nipple that I can use instead of the Jet, bought it from Ted J. Will that work better? Muskrat

Finally get wideband hooked up , fir up engine and have a high pitched sound from turbo, very faint but never heard this one before. Could it be bearings in turbo? If so , what to do. It's always something. BTW 11.0 at idle and drops to 10.2 or so as I throttle up. Ideas, comments? Muskrat

insane Thanks Insane, This sounds exactly what I need to power things. Can I get more info? I suck at electrical. Which ignition wire do I use? Come off the battery into a three fuse box, how does that get turned on exactly? Thanks for the help guys. I do have another issue with innovate ...

I am going to go postal. I am missing out on the best winter in 25 years here all because of a stupid fricking gauge. Innovate LC1 and xd16. The thing says it isnt getting enough volts. I took the hot off ignition switch and sure as heck it is only 11.5 volts. ( Battery is 12.6) when I hook it...

Help Thanks everone. I got something screwed up for sure. I'll download that manual. I ground the blue to a different spot but the gauge is at the same spot as my other gauges. That must be causing the interference. Will it hurt it to drive it that way? Muskrat

Elect Sorry if that's a really stupid question but I suck at electrical. Muskrat

Replacing my Autometer Disco gauge with an XD-16. Can I ground everything to the battery (that's how the Autometer was set up,) or do I need to use the frame. Thanks for the help, I just don't want to fry this gauge. Muskrat