nytro

I was wondering if any of you guys know how full the coolant should be on the nytro (right side over chaincase) I was yesterday no coolant all the way up to the cap, so just wondering if any of you know...

First time poster, love the site. Tons of great info. I just bought an 09 Nytro that had been in an accident and am putting it back together. I realized in doing so when attempting to put the steering back together, that the plate where it connects near the nose is bent. The old steering...

Since everyone and their mother says to go turbo, is there any used kits out there or am I going to have to buy a new one?

Hey guys. I have a 2009 Yamaha nytro and the fuel pump won’t turn on. I have 8.4 volts to the connector instead of 12 and still nothing. The green fuse is good, the 10 amp red fuse is good, and the relay clicks when the key turns. Tried two different good relays, swapped fuses, and tried two...

Ok so I just picked up a custom 2010 Turbo Nytro, 270 HP turbo, turbo smart wastegate and boost controller, msd auxiliary fuel pump, boondocker fuel control. Shimmed so it runs on 91 pump fuel. My question is, how do I use it lol. I have no clue what the boost controller is set too, if I turn...

Hi guys, looking to piece together a Hurricane power up kit. Contacted Dave at Hurricane and he said that hindle no longer makes a header for the Nytro. Currently have a SKINZ ultra q muffler and curious if a mbrp header would work? Also looking for input on pc5, modded air box, clutching, etc...

Now Offering billet aluminum ignition retainer/ jam nuts for any of the 2000s 4 stroke sleds, same nut used on the 2 strokes also. So will fit apex,nytro,vector,rx1, srx,sxr,vmax sx,phazer etc. Have raw machined and anodized red available. $15 usd +shipping per hex nut. Will have blue available...

Having trouble with too low idle when engine is hot. Drops down to 750-1000 rpm and can just die out. Idles normal when cold. Have checked throttle cable and tried to adjust both ways without any changes other then activating TORS. Also tried changing CO settings, everything between -15 to...

I have a 2008 Nytro RTX, the engine went bad so I replaced the engine with one out of a 2009 Nytro. The engine is in and will start up fine, as soon as the temperature light goes out the idle drops and the engine dies. The engine will run if the throttle is held slightly open. I have found...

I recently lost oil pressure in my 2008 40th anniversary nytro RTX and now the engine is toast. I found a good deal on a 2009 nytro engine I’m not sure if it’s a base/RTX/XTX but it has a 121” track. Will the engine fit in my 2008 chassis and will the 2008 wiring harness work?

So here is the issue I can not get resolved , my sled is a 2009 Yamaha nytro xtx with a mpi supercharger 180 kit , full exhaust gems controller , the sled was running great and last week I was out on the lake and it was running great then after a long pull across the lake it started to sputter...

Wondering if artic cat 162 rails with work with my timbersled mtn tamer skid out of my nytro for my nytro! TIA

Hey guys new to the 4 stroke world and this forum. Recently picked up a 13’ nytro with 1500km thats been sat a while so tonight I decided to change the fluids. Question is should the oil be checked when hot or cold? Ive searched but cant find a straight answer. I added 3.3L after oil was drained...

Hi guys, having an issue with my 2011 nytro, push turbo kit. 4000 miles, koso afr gauge, push turbo (gems?) Fuel controller. Last season I noticed it hunting rpm's at idle when cold, between 1200-2200 I bought it this way. I thought it was just normal, maybe something to do with the turbo kit...

Did a pretty wide search, and a BUNCH of good reading, and... I'm wondering if anyone has run with both the Split Rail skis and 43/2" Mountaintech arms. It's my understanding that the Split Rail knuckles changed the steering geometry, wondering how this interacts with the Mountaintech modified...

Yamaha nytro xtx 2013 turbo 3tkm driven made weird sound today like "sluush" when i started driving and itit continu make weird noises, then it stopped and i continue frive. After 2km i stopped and it made same loud sound and i slowly drove it home, theres allso continous blowing sound when...

First time messing with a snowmobile track here.... I just recently installed a few new bogeys on my 2009 Nytro xtx. I'm just wondering if I have to tighten/loosen the back idler wheels for the track to adjust or how it works? Also, how am I supposed to line it up exactly? Thanks!

Does anyone by chance have any videos or pics of doing a shim and turbo install?? I'm gonna try and tackle it my self. Also can I get away without a shim and run low boost?

I was working on replacing my lower a-arm ball joints and have questions around once the new ones are in how stiff are they supposed to be. One I pressed in (and it did press in evenly) i can't move will my fingers but if i put a bolt in it moves but stiffly. I had trouble with this one...

What's the difference between the Nytro PC5 and the Viper PC5. And will either one work on a 14 xf 7000. Been trying to get in touch with Ulmer racing but no luck yet! Thanks.