BLUEBALLER
Expert
- Joined
- Jan 29, 2005
- Messages
- 420
- Reaction score
- 3
- Points
- 491
As requested - Good Luck!!
Parts Needed
Hotgrips - model # 8ED - BK (long) or # 88T - BK (short) - $49.95 pair
Power Resistors - 1 Ohm, 10 Watt - Radio Shack model # 271-131 - $1.99
Bar ends - Sportech's, RSI's, Yamaha, take your pick - the Yamaha ones needed to be ground down to fit inside the 7/8" bars, not too sure on other brands. approx. $18 each.
Tools Needed
soldering iron, wire cutters, heat shrink/electrical tape, zip ties, cordless drill, rivet gun/rivets, utility knife, scotch brite or sandpaper, pipe cutter/hacksaw/sawzall, file, grip adhesive.
Installation Instructions
Here's the order in which I performed task:
1) Remove hood. Trace each handwarmer wiring back to connectors & disconnect both. Cut open handgrips using utility knife - watch for adhesive on the hooked bar ends. Drill out both rivets on each handgrip.
2) Pull heating element cables out of grey wire loom, cut off at handlebars & set cables aside. Use utility knife & sandpaper/scotchbrite to remove heating elements from handlebars until smooth.
3) Measure where you want to cut off hooked portion of handlebars. I used one of the rivet holes as a reference - cut off bar hooks.
4) File off any burrs - inner & outer. Slide Hotgrips on and make sure you have clearance where needed - brake, throttle, etc.
5) Drill new holes into handlebars for new rivets - install rivets later. Run Hotgrip cables into wire loom & pull out at wire harnesses.
6) Decide where/how you're going to mount power resistors. Cut original cables (with harness attached) to desired length & leave outer rubber sheave on. If you're using heatshrink, install it now. Solder in Power resistor as instructed. Cut other wire to length & solder hotgrip to oem cable ( other wire in harness) Add 7.5 Amp fuse in series with resistor if desired. I was going to, but decided it wasn't necessary.
7) Decide where you are going to mount power resistor & mount using zipties - I used 3 zipties per resistor to secure soldered ends & resistor itself.
8) Repeat for other Hotgrip.
9) Plug in harnesses.
10) Add aftermarket bar end if desired.
11) Fire up sled and FEEL the HEAT!!!
Once you are satisfied - glue em up & add rivets.
Parts Needed
Hotgrips - model # 8ED - BK (long) or # 88T - BK (short) - $49.95 pair
Power Resistors - 1 Ohm, 10 Watt - Radio Shack model # 271-131 - $1.99
Bar ends - Sportech's, RSI's, Yamaha, take your pick - the Yamaha ones needed to be ground down to fit inside the 7/8" bars, not too sure on other brands. approx. $18 each.
Tools Needed
soldering iron, wire cutters, heat shrink/electrical tape, zip ties, cordless drill, rivet gun/rivets, utility knife, scotch brite or sandpaper, pipe cutter/hacksaw/sawzall, file, grip adhesive.
Installation Instructions
Here's the order in which I performed task:
1) Remove hood. Trace each handwarmer wiring back to connectors & disconnect both. Cut open handgrips using utility knife - watch for adhesive on the hooked bar ends. Drill out both rivets on each handgrip.
2) Pull heating element cables out of grey wire loom, cut off at handlebars & set cables aside. Use utility knife & sandpaper/scotchbrite to remove heating elements from handlebars until smooth.
3) Measure where you want to cut off hooked portion of handlebars. I used one of the rivet holes as a reference - cut off bar hooks.
4) File off any burrs - inner & outer. Slide Hotgrips on and make sure you have clearance where needed - brake, throttle, etc.
5) Drill new holes into handlebars for new rivets - install rivets later. Run Hotgrip cables into wire loom & pull out at wire harnesses.
6) Decide where/how you're going to mount power resistors. Cut original cables (with harness attached) to desired length & leave outer rubber sheave on. If you're using heatshrink, install it now. Solder in Power resistor as instructed. Cut other wire to length & solder hotgrip to oem cable ( other wire in harness) Add 7.5 Amp fuse in series with resistor if desired. I was going to, but decided it wasn't necessary.
7) Decide where you are going to mount power resistor & mount using zipties - I used 3 zipties per resistor to secure soldered ends & resistor itself.
8) Repeat for other Hotgrip.
9) Plug in harnesses.
10) Add aftermarket bar end if desired.
11) Fire up sled and FEEL the HEAT!!!
Once you are satisfied - glue em up & add rivets.
Attachments
ShootToThrill
VIP Member
Does anyone happen to know the resistance in the '06 Apex updated bars as I still have mine. I'll try to check. Maybe I can use these to cut and modify for my Nytro then when its time to trade in just put the original bars back on? Dang another project! Thanks for the info BlueBaller!
Thanks Blueballer for the instructions that even a pipe welder can follow. Very much appreciated, especially when my hands aren't freezing this winter,
Deadman
Expert
I assume this is good for the 09's too?
LJ 452
TY 4 Stroke God
If you read the other thread about this there is more info. To answer your question, mine measure 6.8 ohms per grip.cwcsrx700 said:
Swiss Sledder
TY 4 Stroke God
- Joined
- Apr 18, 2003
- Messages
- 2,792
- Reaction score
- 6
- Points
- 816
- Location
- Bidford on Avon, United Kingdom
- Website
- www.mi5.gov.uk
Awesome job with the write up Blueballer and thanks for taking the time to do this.
Site Members, this is an excellent example of how a problem was solved by a guy from this site. Rather than sitting back and complaining, he took action to solve the problem and took the time to document the solution. He has demonstrated a good example for everyone to follow.
Site Members, this is an excellent example of how a problem was solved by a guy from this site. Rather than sitting back and complaining, he took action to solve the problem and took the time to document the solution. He has demonstrated a good example for everyone to follow.
towerrigger
TY 4 Stroke Junkie
Beauty, nice work Blueballer! I take back most of the bad things I said about manatobians! 
ShootToThrill
VIP Member
LJ 452 I believe they are talking about the original '06 Apex bars. I have the 29.99 updated bars.
LJ 452
TY 4 Stroke God
cwcsrx700 said:
The Original 06' (bolt-on bar ends) measured something like 2.2 ohms per side or something. The measurement of 6.8 ohms per grip that I gave is for the updated 06' bars (one piece). Which are the same (at least the grip and heater) as everything since.
ShootToThrill
VIP Member
Thanks LJ452!
apltx08
TY 4 Stroke God
BLUEBALLER would this set-up work on my '08 APEX
Deadman
Expert
is this necessary for the 09's?
marsh14
Expert
Buy a pair of heated gloves, no time wasted, problem solved.
arteeex
TY 4 Stroke Master
Heated gloves from Gerbing's seem like a good idea, but what would we do with all the time we would save by not working on the sled, talk about our feelings? This just doesn't seem very manly.
http://www.gerbing.com/Products/gloves.html
http://www.gerbing.com/Products/gloves.html
BLUEBALLER
Expert
- Joined
- Jan 29, 2005
- Messages
- 420
- Reaction score
- 3
- Points
- 491
I'm going to an open face helmet this year cause I hated the cord. I couldn't imagine having my hands plugged in as well.
Different strokes for different folks. If that's the route you choose, good luck with it.
I'm not sure if this is necessary for the 09's - nobody's measured their handwarmers yet.
Should work fine on the 08 - double check your heating element resistance then you'll know for sure. If they measure 6-7.5 ohms, then give'r
Different strokes for different folks. If that's the route you choose, good luck with it.
I'm not sure if this is necessary for the 09's - nobody's measured their handwarmers yet.
Should work fine on the 08 - double check your heating element resistance then you'll know for sure. If they measure 6-7.5 ohms, then give'r
