Search results

a friend of mine has one with the big 28 rs from jeff and it is starting to come ( to much horse power breaking jack shafts for example. let me know of your e mail and i will send you the new pic with the rx1 engine that was last year with the 925 doo it ran 9.50's at 144mph.

ran this week end 1st time out need to try to hook up i dont know much about this proline gets out to at 1.55 60 and is almost sidways until half track yaaahoooo. lower the frt more and helped. got down to 9.61@145mph. running17 lbs with rear mount mcx. had 130's and went to 140's and gained 6...

ttt

do you have the rear air transfer shock in it. if not get one they work well . more pressure less wheelie if yes m-10.

http://www.rx1.info/viewtopic.php?t=13178 can some one help me on the easy way of this[/code][/list][/url] try out apex with large frt mount

what about a 28rs will it fit also

i hear ya what to do. i also want to asfault mine and if i take it apart to get ac bs tunnel i should be able to get it togethrer

meat remember its a fuel screw not air. the further out the more fuel it gives it. i run mine at 2 and needles on # 2 we ride 4-8000 ft

fuel press to low or leaking t's what was used to seal them. the yamabond worked perfect and will stay more plyable. is it worse at higher boost settings

forcast looks good hope we will be able to see as the snow is coming :Rockon: :Rockon: :yam: :drink: :drink: :drink:

i agree 100% that more helix will load motor harder faster and build boost quiker. have you had it over 13# yet. are you going to the biso?does yours pop at all in the bottom end?

is that sled have a rmi drive in it because it would be the ultimate test eh. darryn

gat one from your local catt dealer off an old ext and yes the brown wire going to kill button in serise

i resealed my tee's today i had used a 2 part apoxy and now i used 1104/ yamahabond and it will seal way better .cant wait to try to see if my low end brap brap brap then it pulls like normal (hard). this was worse with 17lbs. is yours ok at 10 but not when you turn up the boost? mine did it...

i am going to redo mine as i have some braap,braap befor it will go. this site :Rockon: for stuff like this. need it top notch for the biso

mine was doing that also then it would take off. i had put my needles on # 2 when i built it. it was worse at lower alt. put up to #3 and now its gone. it was a pain when you were pulled up to someone to race and it hessitated for a couple of seconds then took off. (at 10 or 19lbs). where are...

spend the $$ on a nice boost controller manual ones' waste boost pressure (buy bleeding off line) i have the turbo smart 2 stage works perfect. did any expose dial's for adjustment just incase more is needed. that would be a nice thing about a frt mount eh

call darryl baker at racer's edge in calgary he has lots as all his new ones are frt mounts. if you need his # let me know but i am sure you know it

no only off 2 center ones and yes used 5/16 NEED MORE T'S I GUESS. works perfect for the week end drags till i get more tttttttttttttttttttttttttttttt's nothing is leaking it works perfect the normal way.

it works fine at 10 lbs but fuel press needs to be higher for 17lbs i just got back and wouldnt accelorate and would pop. put it back to intercooler and was perfect. last night changed to 132.5 and put my float level to 15mm (was 10.5) nowreads perfect on stoitch and pulls hard, compared to the...