Search results

Disregard, TORS was frozen, thawed it out and ran like a top. After looking at the error codes, I was worried about ECU, instead, I'm just a moron.

I apologize because I'm sure the answer is in here, I just haven't found it. '06 Apex RTX, it's been running great and last rode it Saturday in heavy wet snow. Temp plummeted and didn't ride on Sunday. This afternoon, started it up, idled great, idle dropped when warm, went to ride and...

Thanks for the replies. The sled is blowing oil out of the exhaust. Research has led me to believe it is a ring issue on the '03. Figured a new top end is the cure. Sounds like a pass on the job. It's an uncles sled so I will let him know to keep checking the oil level and it should be ok...

Is there a thread on a top-end rebuild for an 03 RX-1 (preferably with pics)? Done 2 stroke rebuilds, will this be much different (take carbs and air box off, drain coolant, remove head and cylinders and reverse for assembly)? Thanks. Todd Westfield, IN

Does anyone know what track clips are needed for a Camoplast Ice Ripper XT? I can't find anything online. Thanks. Todd Payne

No problem with the "ny" in the nylock melting?

Replacing my Y-Pipes on my 06 Apex. I removed the y-pipe bracket that is riveted to the tunnel. Should I just rivet it back or stainles steel bolts and nuts (I giggled when I typed "nuts")? a couple of the rivet holes are enlarged. Should I drill those out and used bolts on just those...

Thanks again for for the replies and FINALLY got it.

Thanks, didn't want to bend the tabs without hearing it first. Been drinking too much to try it now, maybe in the morning. I appreciate the responses!

Y pipe and exhaust are not separating on an 06 Apex. Everything is unscrewed and disassembled. Think they are jsut stuck. Anyone have any tricks?

Unless the movie is one of the first 2 Lord of the Rings. The movie wasn't over until the 3rd movie so you didn't miss anything.

Another option to look at is behind the primary. I had this happen, when you blow a belt, the cords can wrap around the primary shaft and detroy the seal on the shaft where it enters the case. Mine was covered with belt cord and the seal was gone. The spinning primary shot oil around and got...

I ordered mine through Port Yamaha and I did not recieve any instructions, just the bags with the bushings and the ID's on them.

Did anyone that installed these bushings recieve install instructions? Not that I'm a moron (don't ask my wife), but when I installed them everything went well until the last A arm. The last bushing slide in with no issues and not snug at all. The bolt would not fit in the bushing. Contacted...

Ok, I installed the bushings per Ulmers instructions, both flanged heads torwards the front. I seem to have more forward and backward movement in the bolts than I had before. You can see in the picture i can get the tip of a medium flathead between the bolt and the flanged head. It is torqued...

Found trhis in an old message I had saved. Just plug and play! Here is a part number for the harness you're looking for...it goes for less than $20 at the dealer. 90891-50150-00 If installed on a 2006 Apex witht the stock 2006 bars you will have HOT bars. Read more on here about this...

So I found the regulator in the front of the sled. I disconnected it and took it out. Inside the light gray connector I found engine oil. HOW IN THE F*&^ DID THAT GET THERE?????? Was able to clean out the the regulator male side, but I need to figure our how to clean the oil out of the...

Thanks Blue ER. Apparently I must have made sound pretty knowledgable on accident (I'm not) but I do not know which part the crossover and where is the regulator located? Thanks. Todd

Ok, as usual for the new seasonof my '06 Apex RTX, did my usual oil change with filter and plug change. Realized my battery wasw totally dead and not taking a charge. I picked up a new battery, however, it's is not a Yuasa battery, it's a bike battery that says it replaces the YTX14-BS (or...

I appreciate the quick response. Hope it is that easy. Thanks again.