rx1

Got a 2003 RX-1 that starts right up with choke on, then idles perfectly. When I hit the throttle it stumbles (and will die if pressed). If I put the choke half on, it will rev up so it's definitely a lean issue. I have gone through the carbs multiple times, all jets are clean, new pilot jet...

I've looked a lot on any similar problem without any luck. After a long ride in a trailer without a cover on, the dashboard console is no longer powering on. Brake and headlights are on, the fuses are OK, the relays also. I've checked the entire harness that connects to the console and there...

So I went to start my sled the other day to go fishing and noticed the gauge wasn’t working right, it comes on then goes off. Tach does not work will sit at 0 then up too 2.5rpm if I hit the gas it glitches back off. When the tach comes on so does the rest of the gauge can control hand and...

Hey guys, I'm fairly new here but I'm just looking for some potential guidance in regards to a little oil I found underneath my snowmobile. I recently changed the oil as well as the oil filter and I'm wondering if maybe I didn't tighten something fully or if I accidentally pinched or hit a line...

Sold my ‘03 Rx-1 last season which I owned from new but before selling it I removed all aftermarket parts which I added over the years. One being the now discontinued GP-1 White Knuckle Exhaust. I’m now thinking it’s just something I’ll end up moving around in my garage for years to come...

Hi everyone, Im looking for a new rear skid for my 2003 Rx1. Is there any easy bolt on skids from an apex that would fit with minimal hassle. I was looking at a 2006 Apex skid, and was wondering if it would fit. Any suggestions?

HI everyone - I am trying to create my own RX1 decals and need a high res photo so I can trace in Adobe Issustrator. Can someone take a high res photo of just the RX1 Logo and send it to me?

. Rx1 seat mod 3" of saddle foam (firm) with two stage carbon fibre seat heat....4way stretch vinyl with custom stitching on top panel. All seat work done by Jody Graham of Custom line located in Huntsville, Ontario, Canada. Same price as a used apex seat in great condition way cheaper than...

Ive got a rx1 with a turbo kit on it. I also have a nytro without a turbo. Im just wondering if its possible to swap the turbo to the nytro? Rx1 isnt running anymore and would love to boost the nytro. Im a welder so any welding mods would be easy. Just wondering about fuel injected nytro carbed...

Hey all ! Im just wondering if its posible to put the turbo kit from my rx1 onto my nytro? I dropped a valve in the rx1 so im thinking why not swap if i can. Has this been done? Can i get away with modifying the intercooler or is there room under the tight hood. Any and all info will be very...

Hey all!! Just got my old rx1 turbo fired up after a year and a half. It idles nice and smoke free at first then starts smoking like crazy. Im thinking its comin from my turbo. Just wondering if theres a way to pull it apart to determine if thats it? Any and all help would be great. Thanks for...

Hey all!! Ive got an 03 rx1 and the 3 bolts that bolt the flywheel setup to the magneto have sheered off. Luckily it didn't seize my engine. I was lucky enough to spin the bolt ends out of the mag with my thumb but ive only found 2 of 3 bolt heads. I cant stomach the thought of putting it back...

Hi. I recently bought a 2004 rx1 with a 240 turbo kit installed. When i start it up when cold it idles fine, i wait for the warmup light to turn of and then drive it really slow for 2-3 minutes after warming up good the rpm's just holds at About 3000 and it wont come down. If i flick the choke...