Search results

Apex 06 - Thanks for the info on the clutch alignment spec! When I used the SLP Universal Alignment Bar and the offset spec 15mm for my 2007 Yamaha Attak, I was not coming anywhere close to touching the inside of the primary clutch. The photo you provided tells me why. The Yamaha spec is...

I am aligning the clutches on my 2007 Attak GT. I am new to this and just bought a Straightline Performance Universal Clutch Alignment Tool. Although it looks pretty cool and functional, I was disappointed that it did not include any Yamaha clutch offset settings. The directions had the...

AK Yammy - looks like nearly identical break as mine AK Yammy - which bolts are you referring to that were loose? 5mm Allen bolts up front under the round rubber plugs? OR the 12mm hex bolts further back under the oval rubber plugs? Thanks!

Attached are photos of my 2007 Yamaha Attak exhaust/silencer assembly. Notice the hole in the system where the 2 pipes reduce to a single pipe before the muffler. Looking for advice from others that have had similar issue. Can this be welded up? What is the material? Will a weld hold up...

I heard some rattling like a clamp or bracket was loose after start up and then my 2007 Attak GT got very loud! Sounds like it is in exhaust leak in the middle of the exhaust system under the seat. I had the donuts done by the dealer at the end of last season under YES warranty and have only...

Got the mono installed and learned a few tricks in the process after reading some posts and trial and error of a few approaches: Detach the transfer rod at front mounting position Detach limiter strap at bottom Raise skis up on blocks about 4-6 inches - helps provide some clearance in front...

Were you in the wrong hole? (I hate it when that happens!)

I was charging my 5 year old battery and my charger is telling me its a little weak and probably due for replacement. I have generally had very good luck with the YUASA batteries that come as OEM equipment on my sleds (The YUASA battery on my 2005 Doo is still going strong - even after being...

Do you know the spring hole positions and the twist angle specs for your sled? I have an 07 Attak and my spring hole positions are 3 for the fixed sheave and 3 for the spring seat with a twist angle spec is 60 degrees. I think yours are probably the same. I noticed your spring is in hole 6 of...

Unfortunately I do not have a sled lift. I am lifting the back of the sled with a cable hoist that is attached to my garage ceiling. This is part of the challenge as it wants to shift the suspension toward the front. That is why I was using ratchet straps to pull the suspension backward. I...

Recently rebuilt the rear suspension on my 2007 Attak GT - New front arm, rebuilt Ohlins EC, new idler bearings, new bushings. I am having a hell of a time getting the suspension back in. I read about and have tried a few tricks including - disconnecting transfer rod from front arm, and...

FINAL VERDICT After a few weeks of waiting I finally got the front arm. The dealer was able to get it covered by Yamaha. He said it was a goodwill gesture by Yamaha as they generally do not cover the arm. I picked it up and I am installing this week. They have significantly beefed up...

Curious - how long are most going between rebuild on Ohlins EC shock for mono skid? Years and miles? How can you tell if the shock needs a rebuild?

I have an 07 Attak GT. What was the issue with the rail caps that required re-design? I have my skid apart doing a front arm replacement and rebuild - would be a good time for me to change these if needed.

For years I did the seafoam/stabil and periodic starting in the off season. After the crank bearing failure and a $1700 rebuild on the wifes sled I have become paranoid. Unfortunately I have too many toys and no longer have a garage stall to store the sleds in. I now store in an enclosed...

Does the A Arm look straight and can you put the bolt (a new straight one of course) through it without forcing it? Mine was not - tried to straighten and was not able to get it straight without binding on the spindle.

Where is the cornering problem? On deceleration into a corner and not able to corner? If so, limiter setting is probably not going to help. Acceleration out of corner? Limiter and transfer rod setting will affect this. I have an 07 Attak GT (Similar to LTX). It took me some...

YammyRX1 Regarding what to use - you can use any fogging oil that can be found in most automotive and marine stores and most discount chain stores. I have used StaBil brand fogging oil as well as Pennzoil Marine Fogging Oil on my 2 strokes. Somebody else will have to chime in on the...

Starting the motor periodically in the off season is NOT recommended. I have heard this from mechanics in the aviation industry, automotive and Yamaha recommends that you not do this in their owners manual. The reason is that you can introduce more moisture and acids into the motor. The...

Dealer has submitted claim (apparently they have an on-line claim system that the dealer uses) and said he thinks Yamaha will cover the part and they will probably not cover the labor. He has ordered the part and is pending confirmation from Yamaha to ensure he is covered for the part. I do...