Paul61001
Newbie
hey i was wonding if anyone has detailed instructions on how to remove the old track and reinstall a new one. pics would be great. i have access to a lift at work so that should help by lifting the rear and sliding out the suspention. thanks for the help
Paul61001
Newbie
P.S. its a 09 Phazer RTX if that makes a difference
Not detailed but first remove Chaincase cover and lower gear,Remove suspension next.Then you will see the bearing for driveshaft is in a housing that is removable.Remove it.Then go to other side and unbolt the three bolts holding the flange bearing in.Push track as far up into front of tunnel as you can and then pull diveshaft toward chaincase.Shaft will fall out at this point.Change the leftside bearing and reverse procedure to install new track.Look for a arrow on track so it is on right direction.Arrow goes track direction.
yam177
TY 4 Stroke Master
Phazer is an easy sled to change the track on. I did one once in 50 min during a lunch break at the race track!!!
Just follow what Cannondale said its relay quick!! Disconnect the battery as well to prevent any chance of arcing,,,,
Just follow what Cannondale said its relay quick!! Disconnect the battery as well to prevent any chance of arcing,,,,
RedPhazer
Expert
Cannondale, what do you mean by 'change the left side bearing'? Is this just a precaution since it wears? Or, did you mean re-install the left side bearing?
Go with Cannondales directions, It isn't that bad of a job. i had never doen one and I thought it was pretty easy.
good luck.
good luck.
RedPhazer said:Cannondale, what do you mean by 'change the left side bearing'? Is this just a precaution since it wears? Or, did you mean re-install the left side bearing?
Yes just a precaution.At least regrease it while its out though.
RedPhazer
Expert
Sounds too easy... might have to dial up tracksusa.com and try the 136" kit!
yam177
TY 4 Stroke Master
Strut4
Newbie
What size mm nut is holding the lower gear in place?
woolyviper
TY 4 Stroke Master
- Joined
- Mar 24, 2006
- Messages
- 1,151
- Location
- hibbing,mn
- Country
- USA
- Snowmobile
- 2009 Yamaha Phazer RTX
i think it's 14mm
woolyviper
TY 4 Stroke Master
- Joined
- Mar 24, 2006
- Messages
- 1,151
- Location
- hibbing,mn
- Country
- USA
- Snowmobile
- 2009 Yamaha Phazer RTX
woolyviper
TY 4 Stroke Master
- Joined
- Mar 24, 2006
- Messages
- 1,151
- Location
- hibbing,mn
- Country
- USA
- Snowmobile
- 2009 Yamaha Phazer RTX
woolyviper
TY 4 Stroke Master
- Joined
- Mar 24, 2006
- Messages
- 1,151
- Location
- hibbing,mn
- Country
- USA
- Snowmobile
- 2009 Yamaha Phazer RTX
woolyviper
TY 4 Stroke Master
- Joined
- Mar 24, 2006
- Messages
- 1,151
- Location
- hibbing,mn
- Country
- USA
- Snowmobile
- 2009 Yamaha Phazer RTX
once you have all that out of the way, you can work the driveshaft out of the chain case and remove the driver and track.
Similar threads
- Replies
- 5
- Views
- 2K
-
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.