Search results

Need to replace the rear bumper in my buddies red/white '19 Sidewinder LTX SE but it appers the red bumper is no longer available for that model (SW1NLDKS): BUMPER, REAR 1 8JP-K7541-60-00 The other color combo for the '19 SE (SW1NLDKS) has the rear bumper available but not sure what color it...

Having a tough time removing the exhaust donuts from the flex flange so wanted to get some suggetions. On my 08 Apex, the OEM donuts either were so deteriated that there wasn't much left to them or they easily spun. Although all of mine are still intact, my are leaking so want to replace them...

Am in the process of replacing these two joints on the steering shaft. After loosening the nuts, they appeared to be pressed in and had to use a hammer to remove. When replacing them, what have others done to get the joints pressed back in? I don't think you can just use the nut to tighten and...

Last Saturday, the weekend after the TY Give-Away ride, I met a couple at the Tahquamenon Falls Brewery & Pub that owned a red Viper and Sidewinder who had noticed the red Yamaha hat I was wearing and had inquired about where I purchased it. I thought the gentleman had mentioned he was a TY'er...

Is it possible to test headlights via the diagnostics mode without having to fire up the sled? Wanting to check a headlight but as you know with these four strokes, to do that means letting the machine warm up to full temp before shutting down so thought maybe there was another way to do this...

Had the two lower bulkhead oilite bushings needing to be replaced on my 08 Apex so decided to replace the lower bulkhead bolts with the newer style that have grease zerks on the head of the bolt: For those who have swapped out the older style bolt with the new style, did you happen to notice...

Had the two lower bulkhead oilite bushings needing to be replaced on my 08 Apex so decided to replace the lower bulkhead bolts with the newer style that have grease zerks on the head of the bolt. When ordering the bolt, the grease zerk is separate so you have to thread it onto the bolt head...

I needed to add radiator fluid to my Apex and know of the bleeder screw on the rear heat exchanger needs to be higher than radiator cap and reservoir when bleeding system so pushed my sled down the ramp of my trailer so nose was lower than rear. As I added fluid, I ensured the level did not go...

Hey Rock, how goes it. Just compiling my snowmobile shopping list for this year and was curious to know if you've made any progress on the remote headlight adjuster for the Apex. I know you have them for the Vipers and Sidewinders and thought the last time I was over at your shop, you had...

Just got back from the U.P. for what was possibly our last trip up there and wanted to give a shout out to Rock @ Rockz Toyz for helping me get my HIDs fixed for the trip. If you've been on this forum long enough and have ever dealt with Rock, you probably know he will practically drop...

Just wanted to pass along another option to replacing the OEM idler wheels with 135mm ones to help with hyfax wear. When I purchased my used 08 Apex, the owner mentioned he had replaced the idler wheels with the larger ones so when it came time to replacing one, I had a hard time finding them...

Thought I would pass along this information in case it benefits someone else. After searching for some time for a 36mm socket that was deep enough for it to pass the jack shaft and tighten the nut, I wasn't having any luck. I thought there used to be a tool that someone sold that not only...

While I had the brake rotor and caliber off to replace all drive train bearings and seals and replace track, somehow the brake handle must have been pressed which collapsed the two brake pads together. Is there a way to decompress the pistons in the caliber to get the gap back between the pads...

If the northern L.P. gets the snow they are forecasting today and tomorrow, are the trails still even open to make one last trip up north? I did read that in some areas like Mio and Traverse City they have closed the gates on some private properties to protect them from ATV use but didn't know...

I removed my suspension to have my Ohlins shock rebuilt and have a question about the routing of the wire. I was able to search the forum and download information as it pertains to the proper wiring technique for routing the wire around the shock and skid but my question centers around the wire...

I had to split my primary to replace the fixed and sliding sleaves. We were able to make our own tool that utilized the three holes on the backside of the fixed sleave and was able to unscrew the clutch spider. The service manual states that when re-assembling everying and screwing the clutch...

When I was cleaning the carb on my son's Sno Scoot, I think I may have lost an O-ring that sits down in the chamber where the choke plunger assembly screws into. After cleaning the carb, I used an air compressor to blow air down into this chamber and had something hit my cheek when doing so. I...

Guys, I need help on deciding between these two tracks. I'm going to extend my Expert X to a 136" this off-season and am having a tough deciding between these two. I've probably heard as may yays as I've heard nays for the Ripsaw but haven't heard too many bad things about the 9819. I'm...

When I as the Novi Show last fall, I stopped by their booth and ever since have been comtemplating purchasing their software. It looks like a really sweet software package. The only drawback is that they only support Garmin GPSs which is great for me but might not be for others that don't own...

I seem to have a small exhaust leak and judging by the sound of it, I have pin-pointed it be the exhaust joint (see pic). At first I thought I might need to replace the gaskets but when I took my tank off and the access panel, I noticed I could turn 3 of the 4 clamps by hand. I tried to...