Need help with code 81, grip warmers not working.

Looks like I need number 2 and number 5 in this picture. I remember reading that they had updated the warmers. Will this get me the updated ones?? I would imagine it would.
Not sure if revised heaters or not, I know people have reached out to Rockmeister @ RoczToyz.com (TY member and site sponsor) for his hot hands kit, and other cool goodies, I have his HIDs on my sleds.
*** Also do not forget the grip adhesive!
Call Kevin at Port Yamaha, he will hook you up with top notch service and you get a discount for being a TY member.
 
Save your money for grip adhesive and simply purchase a can of hair spray. Spray the inside of the grip with hair spray. It will aid in sliding the new grip on and when the hair spray dries, it will serve as your adhesive. ;)!
 
YAMAHAHEATERS---------best improvement to my sled ever
 
Not sure if revised heaters or not, I know people have reached out to Rockmeister @ RoczToyz.com (TY member and site sponsor) for his hot hands kit, and other cool goodies, I have his HIDs on my sleds.
*** Also do not forget the grip adhesive!
Call Kevin at Port Yamaha, he will hook you up with top notch service and you get a discount for being a TY member.

Kevin wasn't available when I called but the gentleman who I spoke with got me hooked up. I have new hand warmers and grips on the way. Anyone who has changed them before and has any advice I'm all ears.
 
It's stupid easy. Trace the wire back and reroute the new ones the same way. Be sure you have your left and right straight, as they are not the same.

Be sure to have a pop rivet tool, and hair spray as recommended. Good luck!
 
Kevin wasn't available when I called but the gentleman who I spoke with got me hooked up. I have new hand warmers and grips on the way. Anyone who has changed them before and has any advice I'm all ears.
I did left one on my 09, used a razor knife and cut old grip off, drilled out rivet, peel off element.
Install element, add adhesive, push on the grip, add pop rivet. Allow to dry.
FYI, since you have an 06 has the handle bars been upgraded to 07 bars like was suggested earlier?
 
I did left one on my 09, used a razor knife and cut old grip off, drilled out rivet, peel off element.
Install element, add adhesive, push on the grip, add pop rivet. Allow to dry.
FYI, since you have an 06 has the handle bars been upgraded to 07 bars like was suggested earlier?
Sorry my bad I haven't changed my sig. I'm on a 2010 now.
 
The "1" on your meter was probably actually "1__"
A "1" and a few spaces then possibly a "'." such as "1__."

On some meters "1__" or "1__." is the same as OL, and NOT the same as "1." or "1.0" (< these would be One)

OL or "1__" or "1__." Is large, Overload or Infinity basically. (An OPEN circuit/Bad grip)
A "1.0" is ONE as in 1 ohm or 1 volt.

Hope this helps!

Rockmeister :-o
 
Last edited:
The "1" on your meter was probably actually "1__"
A "1" and a few spaces then possibly a "'." such as "1__."

On some meters "1__" or "1__." is the same as OL, and NOT the same as "1." or "1.0" (< these would be One)

OL or "1__" or "1__." Is large, Overload or Infinity basically. (An OPEN circuit/Bad grip)
A "1.0" is ONE as in 1 ohm or 1 volt.

Hope this helps!

Rockmeister :-o
Yeah, what he said.....
 
The "1" on your meter was probably actually "1__"
A "1" and a few spaces then possibly a "'." such as "1__."

On some meters "1__" or "1__." is the same as OL, and NOT the same as "1." or "1.0" (< these would be One)

OL or "1__" or "1__." Is large, Overload or Infinity basically. (An OPEN circuit/Bad grip)
A "1.0" is ONE as in 1 ohm or 1 volt.

Hope this helps!

Rockmeister :-o


Thanks Rock, Thats exactly what I was seeing. Love your products!!! Just installed my starter saver and digging out my old trail jamz system to see if I can revive it. I got out of riding for about 5 years and I'm just getting back into it.
 
You are welcome, is good info for all.
Thank you, we work hard to take great care of everyone!

(lol, Liked the: "Yeah, What he said" aka 03 RX1 )

Shouldn't be much to reviving your Trail Jamz other than fully charging your player overnight.
Let me know if I can help!

RockMeister :Rockon:
 
Last edited:
im interested in the parallel wire harness upgrade. sounds like a great idea. this from yamaha?
 
I finished installing the new handwarmers yesterday. I fired the sled up and put them on high and within 5 minutes they started to get warm. I’m excited to see if they outperform the originals. My sled is a 2010 so it was supposed to have better handwarmers from the factory but they’ve sucked from new. Unfortunately I’m currently nursing a knee injury so I don’t know when I will be able to actually ride the sled to see how they perform.
 


Back
Top